Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision |
slice:qt [2019/08/22 22:29] – [Entering Values] Michael Radunsky | slice:qt [2019/09/18 13:18] – [Specifications] Michael Radunsky |
---|
| Temperature Stability | ±0.2 mK over 1 hour((Plant-dependent; value specified for D2-100 laser)) | | | Temperature Stability | ±0.2 mK over 1 hour((Plant-dependent; value specified for D2-100 laser)) | |
| Precision | ~1 mK | | | Precision | ~1 mK | |
| Control Capacity | 35 W((User-distributable over four channels)) | | | Control Capacity | 40 W total((User-distributable over four channels)) \\ 20 W max for a single channel | |
| Current Capacity | 6 A per channel((Subject to 35 W overall maximum)) | | | Current Capacity | 6 A per channel((Subject to 40 W overall maximum)) | |
| Compliance Voltage | ≤18 V((automatically adjusted)) | | | Compliance Voltage | ≤18 V((automatically adjusted)) | |
| **Input & Output** || | | **Input & Output** || |
| Connections | Host control: USB Type B | | | Connections | Host control: USB Type B | |
</tabcaption></WRAP> | </tabcaption></WRAP> |
| |
| ==== Extendable Legs ==== |
| The SLICE-QTC has four extendable legs (<imgref belly>). Extending the front legs allows easy viewing from above (<imgref qt_prod_shot>) and extending the rear legs (<imgref side>) allows easy viewing from below. |
| |
| <WRAP half column><imgcaption belly|Underside of SLICE-QTC>{{ :slice:dcc:dcc_underbelly_labelled.png |}}</imgcaption> |
| </WRAP> |
| <WRAP half column><imgcaption side|Side view of SLICE-QTC configured for viewing from below>{{ : slice:dcc:slice-dcc_looking_down.png?400 |}}</imgcaption></WRAP> |
| |
===== Front Panel ===== | ===== Front Panel ===== |
To set the temperature set point from the home screen, touch the Setpoint window for the desired channel (circled in red for CH 1 in <imgref home_Tset1>). A long touch will cause a keypad to appear. Enter desired value and touch the accept button. | To set the temperature set point from the home screen, touch the Setpoint window for the desired channel (circled in red for CH 1 in <imgref home_Tset1>). A long touch will cause a keypad to appear. Enter desired value and touch the accept button. |
| |
A short touch will highlight the Setpoint window in yellow (<imgref home_Tset2>). Use rotary knobs to select digit to edit (right knob) and value for digit (left knob).\\ | A short touch will highlight the Setpoint window in yellow (<imgref home_Tset2>). Use rotary knobs to select digit to edit (left knob) and value for digit (right knob).\\ |
<imgcaption home_Tset1|Select Temperature setpoint for CH 1>{{ :slice:slice-qt_set_t_home_1.png?400x254 |}}</imgcaption> | <imgcaption home_Tset1|Select Temperature setpoint for CH 1>{{ :slice:slice-qt_set_t_home_1.png?400x254 |}}</imgcaption> |
| |
It is possible to control the SLICE-QTC from a Windows<sup>®</sup>-based PC using a GUI. In order to use the GUI, you must first download the latest version, connect the PC to the SLICE-QTC, and assign a COM port to the SLICE-QTC. The following describes the steps involved. | It is possible to control the SLICE-QTC from a Windows<sup>®</sup>-based PC using a GUI. In order to use the GUI, you must first download the latest version, connect the PC to the SLICE-QTC, and assign a COM port to the SLICE-QTC. The following describes the steps involved. |
| |
- Download and store the latest GUI executable from the FTP site (Request copy of executable GUI from [[[email protected]|sales [at] vescent [dot] com]]). | - Download and store the latest GUI executable from [[ https://github.com/Vescent| the Vescent FTP site]] (or request copy of executable GUI from [[[email protected]|sales [at] vescent [dot] com]]). |
- Connect the SLICE-QTC to the PC using a USB type B cable. | - Connect the SLICE-QTC to the PC using a USB type B cable. |
- Turn on the SLICE-QTC. | - Turn on the SLICE-QTC. |