slice:dhv:api
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
slice:dhv:api [2020/05/26 23:59] – [Query Response to Trigger In: TRIGIN?] Michael Radunsky | slice:dhv:api [2020/05/27 00:47] – [Set Source of Modulation Signal for CH 2: MODEB] Michael Radunsky | ||
---|---|---|---|
Line 363: | Line 363: | ||
* In the example, CHANNEL 1 will henceforth respond to Trigger In. | * In the example, CHANNEL 1 will henceforth respond to Trigger In. | ||
- | * To query Error Code, use [[slice: | + | * To query response to trigger input, use [[slice: |
---- | ---- | ||
- | |||
==== Query Trigger Out Meaning: TRIGOUT? ==== | ==== Query Trigger Out Meaning: TRIGOUT? ==== | ||
< | < | ||
- | Returns the meaning of a TTL high Trigger Out signal with respect to CHANNEL as seen in <tabref trigout?> | + | Returns the meaning of the Trigger Out signal with respect to CHANNEL as seen in <tabref trigout?> |
<WRAP center round box 60%>< | <WRAP center round box 60%>< | ||
Line 384: | Line 383: | ||
---- | ---- | ||
- | ==== Set Response to Trigger | + | ==== Set Trigger |
- | < | + | < |
- | Returns | + | Returns |
- | <WRAP center round box 60%>< | + | <WRAP center round box 60%>< |
- | ^ Selection | + | ^ Selection |
- | | 0 | CHANNEL | + | | 0 | |
- | | 1 | | + | | 1 | |
</ | </ | ||
- | * In the example, | + | * In the example, Trigger |
- | * To query Error Code, use [[slice: | + | * To query Trigger Out meaning, use [[slice: |
+ | * Setting the Trigger Out to be in sync with CH 1 removes Trigger Out's synchronicity with CH 2 & vice versa | ||
---- | ---- | ||
+ | ==== Query Source of Modulation Signal for CH 1: MODEA? ==== | ||
+ | |||
+ | < | ||
+ | Returns from where CH 1 receives modulation control as seen in <tabref modea?>. | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Response | ||
+ | | 0 | CH 1 accepts its modulation signal from rear-panel SMA connector | ||
+ | | 257 | CH 1 accepts its modulation signal from front-panel Input A BNC connector | ||
+ | </ | ||
+ | |||
+ | * In the example, CH 1 accepts its modulation signal from the front-panel Input A. | ||
+ | * To set from where CH 1 accepts a modulation signal, use [[slice: | ||
+ | * Only one modulation source may be active at a time | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ==== Set Source of Modulation Signal for CH 1: MODEA ==== | ||
+ | |||
+ | < | ||
+ | Returns MODEA? | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Mode ^ Location of modulation input for CH 1 ^ | ||
+ | | 0 | CH 1 accepts modulation signal from rear-panel SMA connector | ||
+ | | 1 | CH 1 accepts modulation signal from front-panel Input A BNC connector | ||
+ | </ | ||
+ | |||
+ | * In the example, CH 1 will accept a modulation signal from the front-panel Input A BNC | ||
+ | * To query the modulation source for CH 1, use [[slice: | ||
+ | |||
+ | ---- | ||
+ | |||
+ | |||
+ | ==== Query Source of Modulation Signal for CH 2: MODEB? ==== | ||
+ | |||
+ | < | ||
+ | Returns from where CH 2 receives modulation control as seen in <tabref modeb?>. | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Response | ||
+ | | 0 | CH 2 accepts its modulation signal from rear-panel SMA connector | ||
+ | | 257 | CH 2 accepts its modulation signal from front-panel Input B BNC connector | ||
+ | </ | ||
+ | |||
+ | * In the example, CH 2 accepts its modulation signal from the front-panel Input B. | ||
+ | * To set from where CH B accepts a modulation signal, use [[slice: | ||
+ | * Only one modulation source may be active at a time | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ==== Set Source of Modulation Signal for CH 2: MODEB ==== | ||
+ | |||
+ | < | ||
+ | Returns MODEB? | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Mode ^ Location of modulation input for CH 2 ^ | ||
+ | | 0 | CH 2 accepts modulation signal from rear-panel SMA connector | ||
+ | | 1 | CH 2 accepts modulation signal from front-panel Input B BNC connector | ||
+ | </ | ||
+ | |||
+ | * In the example, CH 2 will henceforth accept a modulation signal from the front-panel Input B BNC | ||
+ | * To query the modulation source for CH 2, use [[slice: | ||
+ | |||
+ | ---- | ||
slice/dhv/api.txt · Last modified: 2023/12/06 20:39 by Christiana Sasser