slice:dcc
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
slice:dcc [2022/10/12 18:08] – external edit 127.0.0.1 | slice:dcc [2024/03/27 21:07] (current) – Correcting model name to SLICE-DCC-X Thomas Bersano | ||
---|---|---|---|
Line 34: | Line 34: | ||
<WRAP center round box 40%>< | <WRAP center round box 40%>< | ||
- | | **Model** | **Current Rating** | | + | | **Model** |
- | | SLICE-DC-200 | 200 mA | | + | | SLICE-DCC-200 |
- | | SLICE-DC-500 | 500 mA | | + | | SLICE-DCC-500 |
- | | SLICE-DC-1000 | 1 A | | + | | SLICE-DCC-1000 | 1 A |
- | | SLICE-DC-2000 | 2 A | | + | | SLICE-DCC-2000 | 2 A |
</ | </ | ||
===== Purchase Includes ===== | ===== Purchase Includes ===== | ||
Line 97: | Line 97: | ||
| Operation Modes | Constant Current\\ Constant Power | | | Operation Modes | Constant Current\\ Constant Power | | ||
| \\ \\ Maximum Current | | \\ \\ Maximum Current | ||
- | | \\ \\ Current Noise((Constant Current Mode)) ((rms 100 Hz to 1 MHz)) | 1.5\\ 4\\ 10\\ 15 | | + | | \\ \\ Current Noise((Constant Current Mode)) ((rms 100 Hz to 1 MHz)) | 1.5 µA\\ 4 µA\\ 10 µA\\ 15 µA | |
| Current Modulation Input Impedance \\ Rear \\ Front | \\ >20 kΩ\\ 50 Ω or 1 MΩ | | | Current Modulation Input Impedance \\ Rear \\ Front | \\ >20 kΩ\\ 50 Ω or 1 MΩ | | ||
|Modulation Bandwidth((-3 dB point)), ((front & rear modulation input ports))| | |Modulation Bandwidth((-3 dB point)), ((front & rear modulation input ports))| | ||
Line 366: | Line 366: | ||
+ | ===== Warnings and Faults ===== | ||
+ | === Hardware Temperature Exceeded === | ||
+ | Displayed when hardware temperature exceeds a safe limit for an individual channel. Turn off the SLICE-DCC and let the unit cool for several minutes. If problem persists, contact Vescent. | ||
+ | < | ||
+ | === Internal Case Temperature Exceeded === | ||
+ | Dffects both channels and is displayed when the temperature inside the case exceeds a safe limit. Turn off the SLICE-DCC and let the unit cool for several minutes. If problem persists, contact Vescent. | ||
+ | |||
+ | < | ||
+ | |||
+ | === Interlock === | ||
+ | Displayed on both channels when the interlock circuit is open. Double check that the Interlock Key is inserted and in the " | ||
+ | |||
+ | < | ||
+ | |||
+ | === Open Circuit Over Voltage === | ||
+ | Displayed on a channel that is started without a load attached. Double check connections on both the SLICE-DCC and the attached load. If problem persists, contact Vescent. | ||
+ | |||
+ | < | ||
+ | |||
+ | === Possible Fault Detected === | ||
+ | Displayed when current is being output in spite of the channel being disabled.The appearance of this fault indicates a potential hardware failure. Do **NOT** continue to use unit, and contact Vescent immediately. | ||
+ | |||
+ | < |
slice/dcc.1665598102.txt.gz · Last modified: 2022/10/12 18:08 by 127.0.0.1