slice:dcc
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
slice:dcc [2020/04/30 00:24] – [Connecting to the Laser Diode] Michael Radunsky | slice:dcc [2021/08/26 14:26] – external edit 127.0.0.1 | ||
---|---|---|---|
Line 15: | Line 15: | ||
Click here for the [[https:// | Click here for the [[https:// | ||
Click here for the [[https:// | Click here for the [[https:// | ||
- | Click here for the [[https:// | + | Click here for the [[https:// |
Please check back for added functionality. | Please check back for added functionality. | ||
===== List of Warning Symbols ===== | ===== List of Warning Symbols ===== | ||
Line 97: | Line 97: | ||
| Control | | Control | ||
| Operation Modes | Constant Current\\ Constant Power | | | Operation Modes | Constant Current\\ Constant Power | | ||
- | | \\ \\ Maximum Current | + | | \\ \\ Maximum Current |
| \\ \\ Current Noise((Constant Current Mode)) ((rms 100 Hz to 1 MHz)) | 1.5\\ 4\\ 10\\ 15 | | | \\ \\ Current Noise((Constant Current Mode)) ((rms 100 Hz to 1 MHz)) | 1.5\\ 4\\ 10\\ 15 | | ||
| Current Modulation Input Impedance \\ Rear \\ Front | \\ >20 kΩ\\ 50 Ω or 1 MΩ | | | Current Modulation Input Impedance \\ Rear \\ Front | \\ >20 kΩ\\ 50 Ω or 1 MΩ | | ||
- | | Modulation Bandwidth((-3 dB point)), ((front & rear modulation input ports))| | + | |Modulation Bandwidth((-3 dB point)), ((front & rear modulation input ports))| |
+ | | Modulation Input Range | ||
|Modulation Depth \\ SLICE-DCC-200\\ SLICE-DCC-500\\ SLICE-DCC-1000\\ SLICE-DCC-2000 | \\ ±10 mA\\ ±25 mA\\ ±50 mA\\ ±50 mA | | |Modulation Depth \\ SLICE-DCC-200\\ SLICE-DCC-500\\ SLICE-DCC-1000\\ SLICE-DCC-2000 | \\ ±10 mA\\ ±25 mA\\ ±50 mA\\ ±50 mA | | ||
|Modulation Transfer Function | |Modulation Transfer Function | ||
- | | Modulation Input Range | + | | Current Resolution |
- | | Current Resolution | + | |
| Drift | <25 µA/ | | Drift | <25 µA/ | ||
| Power Stability((constant power mode)) | | Power Stability((constant power mode)) | ||
Line 210: | Line 210: | ||
=== Connection to Monitor Photodiode === | === Connection to Monitor Photodiode === | ||
- | Either of the two configurations of the monitor photodiode seen in <imgref mon_pd> will work for the signal proportional to the laser diode power for operating in Constant Power mode. | + | Either of the two configurations of the monitor photodiode seen in <imgref mon_pd> will work for the signal proportional to the laser diode power for operating in Constant Power mode. Depending on how you have completed the monitor photodiode circuit, you may have to adjust the [[slice: |
- | < | + | < |
==== Setting the Operation Mode ==== | ==== Setting the Operation Mode ==== | ||
The SLICE-DCC has two operation modes: Constant Current and Constant Power. | The SLICE-DCC has two operation modes: Constant Current and Constant Power. |
slice/dcc.txt · Last modified: 2024/03/27 21:07 by Thomas Bersano