slice:dcc
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
slice:dcc [2019/08/29 00:41] – [Firmware Update] Michael Radunsky | slice:dcc [2019/09/13 14:03] – [List of Warning Symbols] Michael Radunsky | ||
---|---|---|---|
Line 25: | Line 25: | ||
</ | </ | ||
- | The SLICE-DCC Current Controller is intended for driving laser diodes. | + | The SLICE-DCC Current Controller is intended for driving laser diodes. |
- | {{ d2: | + | {{ d2: |
=====Description===== | =====Description===== | ||
Line 41: | Line 41: | ||
| SLICE-DC-2000 | 2 A | | | SLICE-DC-2000 | 2 A | | ||
</ | </ | ||
- | =====Purchase Includes===== | + | ===== Purchase Includes ===== |
* SLICE-DCC dual-channel Current Controller | * SLICE-DCC dual-channel Current Controller | ||
* AC power cord with appropriate wall plug for you location (if known) | * AC power cord with appropriate wall plug for you location (if known) | ||
* Two 6 ft SMA cables | * Two 6 ft SMA cables | ||
- | | + | * One BNC grounding cap for door safety interlock |
- | | + | |
* Two keys for lock out | * Two keys for lock out | ||
* Final Test Documentation | * Final Test Documentation | ||
Line 85: | Line 84: | ||
If either the key switch is deactivated or the interlock is opened while the system is operating, the SLICE-DCC will stop delivering current and the Enable window will flash red with INTERLOCK displayed (<imgref inter_open> | If either the key switch is deactivated or the interlock is opened while the system is operating, the SLICE-DCC will stop delivering current and the Enable window will flash red with INTERLOCK displayed (<imgref inter_open> | ||
+ | </ | ||
+ | |||
+ | <WRAP center round important 100%> | ||
+ | Never connect or disconnect the SLICE-DCC to/from a laser with the SLICE-DCC energized. | ||
+ | |||
+ | As with __any__ diode laser and controller, improper usage can cause irreparable damage to the diode. | ||
</ | </ | ||
=====Specifications===== | =====Specifications===== | ||
<WRAP center round box 60%>< | <WRAP center round box 60%>< | ||
- | | **Performance((Subject to change without notice))** | + | | **Performance((Subject to change without notice))** |
- | ^ **Parameter** | + | ^ **Parameter** |
- | | Channels | + | | Channels |
- | | Control | + | | Control |
- | | Operation Modes | Constant Current\\ Constant Power | | + | | Operation Modes | Constant Current\\ Constant Power | |
- | | \\ \\ Maximum Current | + | | \\ \\ Maximum Current |
- | | \\ \\ Current Noise((Constant Current Mode)) ((rms 10 Hz to 1 MHz)) | 1.5\\ 4\\ 10\\ 15 | | + | | \\ \\ Current Noise((Constant Current Mode)) ((rms 10 Hz to 1 MHz)) | 1.5\\ 4\\ 10\\ 15 | |
- | | Modulation Bandwidth | + | | Modulation Bandwidth((3 dB)) | DC to >1 MHz |
- | | Modulation Depth | + | | Modulation Depth |
- | | Modulation Transfer Function | + | | Modulation Transfer Function |
- | | Modulation Input Range | + | | Modulation Input Range |
- | | Current Resolution | + | | Current Resolution |
- | | Drift | <25 µA/ | + | | Drift | <25 µA/ |
- | | Power Stability((constant power mode)) | + | | Power Stability((constant power mode)) |
- | | Maximum Compliance Voltage | + | | Maximum Compliance Voltage |
- | | Triggering | + | | Triggering |
</ | </ | ||
Line 188: | Line 193: | ||
< | < | ||
Accepts parameter edits and exits keypad. | Accepts parameter edits and exits keypad. | ||
+ | |||
+ | ==== Extendable Legs ==== | ||
+ | The SLICE-DCC has four extendable legs (<imgref belly> | ||
+ | |||
+ | <WRAP half column>< | ||
+ | </ | ||
+ | <WRAP half column>< | ||
===== SLICE-DCC Operation ===== | ===== SLICE-DCC Operation ===== | ||
The Home screen displays the status of both channels (<imgref home_scr_dcc> | The Home screen displays the status of both channels (<imgref home_scr_dcc> | ||
Line 226: | Line 238: | ||
<WRAP center round box 60%> | <WRAP center round box 60%> | ||
- | | {{ : | + | | {{ : |
| {{ : | | {{ : | ||
</ | </ | ||
Line 325: | Line 337: | ||
From time to time, Vescent will upgrade the firmware for controlling the SLICE-DCC. | From time to time, Vescent will upgrade the firmware for controlling the SLICE-DCC. | ||
===== Serial API ===== | ===== Serial API ===== | ||
- | It is possible to control the SLICE-QTC through serial commands. | + | It is possible to control the SLICE-DCC through serial commands. |
- | More information coming soon. | + | Please contact [[[email protected]|sales [at] vescent [dot] com]] for information. |
===== Maintenance ===== | ===== Maintenance ===== |
slice/dcc.txt · Last modified: 2024/03/27 21:07 by Thomas Bersano