User Tools

Site Tools


ice:servo-peaklock

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
ice:servo-peaklock [2019/12/20 10:17]
Michael Radunsky [Specifications]
ice:servo-peaklock [2019/12/20 10:20] (current)
Michael Radunsky [Specifications]
Line 31: Line 31:
 ^ ^  ICE-CS1-200 ​ ^  ICE-CS1-500 ​ ^  Units  ^ ^ ^  ICE-CS1-200 ​ ^  ICE-CS1-500 ​ ^  Units  ^
 ^ Current Source ^ ^ ^ ^ ^ Current Source ^ ^ ^ ^
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Current range| ​ 0-200  |  0-500  |  mA  | +|Current range| ​ 0-200  |  0-500  |  mA  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Current setpoint resolution |  200  |  500  |  μA  | +|Current setpoint resolution |  200  |  500  |  μA  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Current noise density((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| ​ <​100 ​ |  <​200 ​ | pA /√Hz | +|Current noise density((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| ​ <​100 ​ |  <​200 ​ | pA /√Hz | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​RMS Noise (10Hz - 100kHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| ​ <​50 ​ |  <​100 ​ |  nA  | +|RMS Noise (10Hz - 100kHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| ​ <​50 ​ |  <​100 ​ |  nA  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​RMS Noise (10Hz - 1MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| ​ <​100 ​ |  <​150 ​ |  nA  | +|RMS Noise (10Hz - 1MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| ​ <​100 ​ |  <​150 ​ |  nA  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​RMS Noise (10Hz - 10MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| ​ <​300 ​ |  <​500 ​ |  nA  | +|RMS Noise (10Hz - 10MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| ​ <​300 ​ |  <​500 ​ |  nA  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Absolute accuracy| ​ 2  ||  %  |+|Absolute accuracy| ​ 2  ||  %  |
 ^ Peak Lock Servo ^ ^^ ^  ^ Peak Lock Servo ^ ^^ ^ 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Bandwidth((Calculated based on RF dither frequency of 4 MHz which limits servo bandwidth))| ​ 3   ​|| ​ MHz  | +|Bandwidth((Calculated based on RF dither frequency of 4 MHz which limits servo bandwidth))| ​ 3   ​|| ​ MHz  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Input Voltage Range |  ±1  ||  V  | +|Input Voltage Range |  ±1  ||  V  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Dither Frequency |  4  ||  MHz  | +|Dither Frequency |  4  ||  MHz  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Phase Shift Resolution |  5.6  ||  deg  | +|Phase Shift Resolution |  5.6  ||  deg  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Input Voltage Noise(( Referenced to 50Ω load)) |  TBD  ||  nV/√Hz |+|Input Voltage Noise(( Referenced to 50Ω load)) |  TBD  ||  nV/√Hz |
 ^ Loop Filter Parameters ^ ^^ ^ ^ Loop Filter Parameters ^ ^^ ^
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Proportional Gain (ref to DC Error) |  -22 to +20  ||  dB  | +|Proportional Gain (ref to DC Error) |  -22 to +20  ||  dB  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Proportional Gain Resolution |  2  ||  dB  | +|Proportional Gain Resolution |  2  ||  dB  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Integrator| ​ 3, 10, 30, 100, 300  ||  kHz  | +|Integrator| ​ 3, 10, 30, 100, 300  ||  kHz  | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Differential| ​ Off, Fixed at 3 times integrator pole  || | +|Differential| ​ Off, Fixed at 3 times integrator pole  || | 
-|<​html>​ &​nbsp;&​nbsp;​ </​html>​Differential Gain |  18  ||  dB  |+|Differential Gain |  18  ||  dB  |
  
 ^Electrical Specifications^^^^^ ^Electrical Specifications^^^^^
ice/servo-peaklock.txt · Last modified: 2019/12/20 10:20 by Michael Radunsky