ice:servo-peaklock
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
ice:servo-peaklock [2014/06/30 21:54] – [Specifications] jtshugrue | ice:servo-peaklock [2021/08/26 15:26] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 8: | Line 8: | ||
Please read [[: | Please read [[: | ||
+ | |||
+ | [[http:// | ||
===== Description ===== | ===== Description ===== | ||
Line 16: | Line 18: | ||
===== Absolute Maximum Ratings ===== | ===== Absolute Maximum Ratings ===== | ||
Note: All modules designed to be operated in laboratory environment | Note: All modules designed to be operated in laboratory environment | ||
+ | |||
<WRAP center round box 60%> | <WRAP center round box 60%> | ||
^ Parameter | ^ Parameter | ||
Line 21: | Line 24: | ||
|Environmental Humidity | <60% | | |Environmental Humidity | <60% | | ||
|Environmental Dew Points | <15°C | | |Environmental Dew Points | <15°C | | ||
+ | |||
</ | </ | ||
- | ===== Specifications | + | ===== Specifications |
- | <WRAP center round box 650px> | + | <WRAP center round box 75%> |
^ ^ ICE-CS1-200 | ^ ^ ICE-CS1-200 | ||
^ Current Source ^ ^ ^ ^ | ^ Current Source ^ ^ ^ ^ | ||
- | |< | + | |Current range| |
- | |< | + | |Current setpoint resolution | 200 | 500 | μA | |
- | |< | + | |Current noise density((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| |
- | |< | + | |RMS Noise (10Hz - 100kHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| |
- | |< | + | |RMS Noise (10Hz - 1MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| |
- | |< | + | |RMS Noise (10Hz - 10MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| |
- | |< | + | |Absolute accuracy| |
^ Peak Lock Servo ^ ^^ ^ | ^ Peak Lock Servo ^ ^^ ^ | ||
- | |< | + | |Bandwidth((Calculated based on RF dither frequency of 4 MHz which limits servo bandwidth))| |
- | |< | + | |Input |
- | |< | + | |Dither Frequency | 4 || MHz | |
- | |< | + | |Phase Shift Resolution | 5.6 || deg | |
- | |< | + | |Input Voltage Noise(( Referenced to 50Ω load)) | TBD || nV/√Hz | |
^ Loop Filter Parameters ^ ^^ ^ | ^ Loop Filter Parameters ^ ^^ ^ | ||
- | |< | + | |Proportional Gain (ref to DC Error) | -22 to +20 || dB | |
- | |< | + | |Proportional Gain Resolution | 2 || dB | |
- | |< | + | |Integrator| |
- | |< | + | |Differential| |
- | |< | + | |Differential Gain | 18 || dB | |
- | </ | + | |
- | <WRAP center round box 60%> | + | |
^Electrical Specifications^^^^^ | ^Electrical Specifications^^^^^ | ||
^ ^ Min ^ Typical | ^ ^ Min ^ Typical | ||
Line 55: | Line 58: | ||
|+15V Current Draw (ICE-CS1-500)((Current draw depends on output current to laser diode.)) | 100 | | 600 | mA | | |+15V Current Draw (ICE-CS1-500)((Current draw depends on output current to laser diode.)) | 100 | | 600 | mA | | ||
|-15V Current Draw | | 60 | | mA | | |-15V Current Draw | | 60 | | mA | | ||
+ | |||
+ | |||
</ | </ | ||
Line 80: | Line 85: | ||
</ | </ | ||
+ | < | ||
**Laser Current ** | **Laser Current ** |
ice/servo-peaklock.txt · Last modified: 2021/08/26 15:26 by 127.0.0.1