Differences

This shows you the differences between two versions of the page.

--- ice:dual-current:ice-dc1_-_dual_current_controller [2020/03/11 12:52] – Ben Luey
+++ ice:dual-current:ice-dc1_-_dual_current_controller [2020/03/11 13:11] – Ben Luey
@@ Line 32: / Line 32: @@
 <function=ICEfunc|0=EvtData&1=I:CHANNEL:1;I:ROW:3;F:CURRENT:78.12&2=78.1&3=26>
 Sets the current to CURRENT in in the event table for row ROW and channel CHANNEL.
+<function=ICEfunc|0=EvtNum?&1=I:CHANNEL:1&2=7&3=27>
+Reads the number of jump rows to loop through for channel CHANNEL in the jump event system. Range from 2 - 8. If set to 4, then the sequence of jump rows will be 1,2,3,4,1,2,3,4,1... where the numbers correspond to the **ROW** set when loading data in with the EvtData command.
+<function=ICEfunc|0=EvtNum&1=I:CHANNEL:1;I:NUMBER:5&2=5&3=28>
+Sets the number of jump rows to loop through for channel CHANNEL in the jump event system. Range from 2 - 8. If set to 4, then the sequence of jump rows will be 1,2,3,4,1,2,3,4,1... where the numbers correspond to the **ROW** set when loading data in with the EvtData command.
+<function=ICEfunc|0=EvtJRow?&1=I:CHANNEL:1&2=3&3=29>
+Returns the next row that the will be read from the Event Jump Table when the device gets an event matching the event set with the **EvtJUMP** command for channel CHANNEL.
+<function=ICEfunc|0=EvtJRow&1=I:CHANNEL:1;I:NEXT:3&2=3&3=30>
+Sets the next row that the will be read from the Event Jump Table when the device gets an event matching the event set with the **EvtJUMP** command for channel CHANNEL.
+<function=ICEfunc|0=EvtJump?&1=I:CHANNEL:1&2=6&3=31>
+Reads the event address that channel CHANNEL lists to for jumping the laser current. Address range is 0-7 where address 0 is no event.
+<function=ICEfunc|0=EvtJump&1=I:CHANNEL:1;I:ADDRESS:5&2=5&3=32>
+Sets the event address that channel CHANNEL lists to for jumping the laser current. Address range is 0-7 where address 0 is no event.
+<function=ICEfunc|0=EvtLOff?&1=I:CHANNEL:1&2=4&3=33>
+Reads the event address for turning the laser off on channel CHANNEL. Address range is 0-7 where address 0 is no event.
+<function=ICEfunc|0=EvtLOff?&1=I:CHANNEL:1;I:ADDRESS:2&2=2&3=34>
+Sets the event address for turning the laser off on channel CHANNEL. Address range is 0-7 where address 0 is no event.
+<function=ICEfunc|0=Pulse?&1=I:CHANNEL:1&2=On&3=35>
+Returns the state of the laser pulse (whether shunting current away from laser or not) on channel CHANNEL.
+<function=ICEfunc|0=Pulse&1=I:CHANNEL:1;A:STATE:Off&2=Off&3=36>
+Sets the state of the laser pulse (whether shunting current away from laser or not) on channel CHANNEL.