d2:spectroscopy_module_210
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
d2:spectroscopy_module_210 [2016/08/31 10:28] – [Specifications] Michael Radunsky | d2:spectroscopy_module_210 [2019/05/31 13:44] – [Purchase Includes] Michael Radunsky | ||
---|---|---|---|
Line 27: | Line 27: | ||
* D2-210 Spectroscopy Module | * D2-210 Spectroscopy Module | ||
* VPN00463 SMA cable (6ft) | * VPN00463 SMA cable (6ft) | ||
- | Also look for: | ||
* VPN00410 Hirose-to-D Sub 9-pin (shipped under separate line item; specify for use with D2) | * VPN00410 Hirose-to-D Sub 9-pin (shipped under separate line item; specify for use with D2) | ||
* VPN00475 Hirose-to-Hirose power cord (shipped under separate line item; specify for use with ICE) | * VPN00475 Hirose-to-Hirose power cord (shipped under separate line item; specify for use with ICE) | ||
+ | * VPN00367 Adjustment tool | ||
Line 45: | Line 45: | ||
=====Specifications===== | =====Specifications===== | ||
<WRAP center round box 500px>< | <WRAP center round box 500px>< | ||
- | ^ ^ Value ^ Units ^ | + | ^ ^ Value ^ Units |
- | ^**Input Light Level** | + | ^ **Input Light Level** |
- | ^**Photodiode Amplifier** | + | ^ **Photodiode Amplifier** |
- | | < | + | | Transimpedance (signal) |
- | | < | + | | Bandwidth (signal) |
- | | < | + | | Noise @ 5 MHz | < |
- | ^Set Temperature | + | ^ Set Temperature |
- | ^Temperature Stability| | + | ^ Temperature Stability |
- | ^Beam Height| | + | ^ Beam Height |
- | ^Total package Size \\ (L x W x H)| 3.6 x 5 x 1.7 | inches | + | ^ Total package Size \\ (L x W x H) | 3.6 x 5 x 1.7 | inches |
</ | </ | ||
</ | </ | ||
Line 65: | Line 65: | ||
<WRAP center round box 620px> | <WRAP center round box 620px> | ||
- | [{{ : | + | < |
- | <WRAP center round box 420px> | + | <WRAP center round box 420px>< |
Input light passes through an adjustable λ/2 waveplate and polarizing beamsplitter (PBS) that directs a user-controlled portion of the beam to the vapor cells and detectors. | Input light passes through an adjustable λ/2 waveplate and polarizing beamsplitter (PBS) that directs a user-controlled portion of the beam to the vapor cells and detectors. | ||
Line 78: | Line 78: | ||
**Input Connector**** (****6-pin circular)** | **Input Connector**** (****6-pin circular)** | ||
+ | <WRAP center round important 60%> | ||
+ | </ | ||
+ | |||
+ | Power and temperature control signals from the D2-series power bus, the ICE-PB1, or other power supply are made through a 6-pin circular connector ([[http:// | ||
- | Power and temperature control signals from the D2-series power bus or other power supply are made through a 6-pin circular | + | < |
<WRAP center round box 900px>< | <WRAP center round box 900px>< | ||
Line 127: | Line 131: | ||
**Tilt Plate** | **Tilt Plate** | ||
- | A polarizing beamsplitter (PBS) is fixed to a ball joint formed by a truncated steel ball held by a conformal brass ring. Two cone screws clamp the ring against the ball and fix the position of the PBS. See Alignment Procedure below for instructions on how to align and fix the PBS.{{ : | + | A polarizing beamsplitter (PBS) is fixed to a ball joint formed by a truncated steel ball held by a conformal brass ring. Two cone screws clamp the ring against the ball and fix the position of the PBS. See Alignment Procedure below for instructions on how to align and fix the PBS.<WRAP center round box 420px> |
+ | |||
+ | < | ||
**λ/2 Waveplate** | **λ/2 Waveplate** | ||
Line 133: | Line 139: | ||
A waveplate attached to the front plate by magnets can be used to select the splitting fraction of the Tilt Plate PBS. | A waveplate attached to the front plate by magnets can be used to select the splitting fraction of the Tilt Plate PBS. | ||
- | {{ : | + | <WRAP center round box 420px> |
+ | |||
+ | < | ||
d2/spectroscopy_module_210.txt · Last modified: 2024/03/27 15:58 by Thomas Bersano