Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision |
slice:dhv [2020/03/28 01:18] – [Specifications] Michael Radunsky | slice:dhv [2020/03/28 01:31] – [SLICE-DHV Operation] Michael Radunsky |
---|
| {{ :electric_shock.png?100&nolink }} | Potential for electrical shock hazard. | | | {{ :electric_shock.png?100&nolink }} | Potential for electrical shock hazard. | |
| <WRAP important></WRAP> | Important. Pay close attention to manual instructions for optimum results and in order to not damage the device. | | | <WRAP important></WRAP> | Important. Pay close attention to manual instructions for optimum results and in order to not damage the device. | |
| |
</tabcaption></WRAP> | </tabcaption></WRAP> |
| |
| |
==== Extendable Legs ==== | ==== Extendable Legs ==== |
The SLICE-DCC has four extendable legs (<imgref belly>). Extending the front legs allows easy viewing from above (<imgref dcc_prod_shot>) and extending the rear legs (<imgref side>) allows easy viewing from below. | The SLICE-DHV has four extendable legs (<imgref belly>). Extending the front legs allows easy viewing from above (<imgref dhv_prod_shot>) and extending the rear legs (<imgref side>) allows easy viewing from below, for instance, when placed on a shelf above a laser table. |
| |
<WRAP half column><imgcaption belly|Underside of SLICE-DCC>{{ :slice:dcc:dcc_underbelly_labelled.png |}}</imgcaption> | <WRAP half column><imgcaption belly|Underside of SLICE-DHV>{{ :slice:dcc:dcc_underbelly_labelled.png |}}</imgcaption> |
</WRAP> | </WRAP> |
<WRAP half column><imgcaption side|Side view of SLICE-DCC configured for viewing from below>{{ : slice:dcc:slice-dcc_looking_down.png?400 |}}</imgcaption></WRAP> | <WRAP half column><imgcaption side|Side view of SLICE-DHV configured for viewing from below>{{ : slice:dcc:slice-dcc_looking_down.png?400 |}}</imgcaption></WRAP> |
===== SLICE-DCC Operation ===== | ===== SLICE-DHV Operation ===== |
The Home screen displays the status of both channels (<imgref home_scr_dcc>). The data for each channel is arranged vertically. At a glance, for each channel, I<sub>set</sub>, and Compliance Voltage can be read. Touching the blue window labelled Voltage [V] will cause this window to toggle from displaying Compliance Voltage to displaying dissipated Power. | The Home screen displays the status of both channels (<imgref home_scr_dhv>). The data for each channel is arranged vertically. At a glance, for each channel, the ON/OFF status, the output voltage, the nominal bias voltage, the Sweep Range (amplitude) for the internal Sweep function, and internal Sweep function status can all be read. |
==== Setting the Operation Mode ==== | ==== Setting the Operation Mode ==== |
The SLICE-DCC has two operation modes: Constant Current and Constant Power. The operation mode, as with most other operating parameters can be set independently for each channel. To toggle between Constant Current and Constant Power modes, from the Home screen, touch the window labelled either CH X Constant Current or CH X Constant Power. If the channel is in Constant Current Mode, you will be presented with the window seen in <imgref cc_param>. \\ | The SLICE-DCC has two operation modes: Constant Current and Constant Power. The operation mode, as with most other operating parameters can be set independently for each channel. To toggle between Constant Current and Constant Power modes, from the Home screen, touch the window labelled either CH X Constant Current or CH X Constant Power. If the channel is in Constant Current Mode, you will be presented with the window seen in <imgref cc_param>. \\ |