slice:dhv:api
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
slice:dhv:api [2020/05/30 00:14] – [Set Source of Modulation Signal for CH 2: MODEB] Michael Radunsky | slice:dhv:api [2021/12/15 20:57] – external edit 127.0.0.1 | ||
---|---|---|---|
Line 23: | Line 23: | ||
^ Stop Bits | ^ Stop Bits | ||
^ Flow Control | ^ Flow Control | ||
- | |||
To perform an operation, an ASCII-based text message is first constructed from a command and its arguments, and then the message is transmitted to the SLICE instrument through the COM port. The following rules apply: | To perform an operation, an ASCII-based text message is first constructed from a command and its arguments, and then the message is transmitted to the SLICE instrument through the COM port. The following rules apply: | ||
Line 35: | Line 34: | ||
- [Float] refers to a floating point argument that has a decimal point in its value. | - [Float] refers to a floating point argument that has a decimal point in its value. | ||
- | < | + | < |
</ | </ | ||
Line 72: | Line 71: | ||
==== SCPI device information: | ==== SCPI device information: | ||
- | <WRAP center round important 100%> | + | <WRAP center round important 100%> |
- | < | + | < |
Returns SCPI device information. Running System Controller firmware version 1.74 and DHV firmware version 1.18. | Returns SCPI device information. Running System Controller firmware version 1.74 and DHV firmware version 1.18. | ||
---- | ---- | ||
Line 165: | Line 164: | ||
==== Query Output Voltage: OUTVOLT? ==== | ==== Query Output Voltage: OUTVOLT? ==== | ||
- | < | + | < |
Returns V< | Returns V< | ||
Line 435: | Line 434: | ||
==== Query Source of Modulation Signal for CH 2: MODEB? ==== | ==== Query Source of Modulation Signal for CH 2: MODEB? ==== | ||
- | < | + | < |
Returns from where CH 2 receives modulation control as seen in <tabref modeb?>. | Returns from where CH 2 receives modulation control as seen in <tabref modeb?>. | ||
Line 441: | Line 440: | ||
^ Response | ^ Response | ||
| 0 | CH 2 accepts its modulation signal from rear-panel SMA connector | | 0 | CH 2 accepts its modulation signal from rear-panel SMA connector | ||
- | | 257 | CH 2 accepts its modulation signal from front-panel Input B BNC connector | + | | 513 | CH 2 accepts its modulation signal from front-panel Input B BNC connector |
</ | </ | ||
Line 452: | Line 451: | ||
==== Set Source of Modulation Signal for CH 2: MODEB ==== | ==== Set Source of Modulation Signal for CH 2: MODEB ==== | ||
- | < | + | < |
Returns MODEB? | Returns MODEB? | ||
Line 489: | Line 488: | ||
<WRAP center round box 60%>< | <WRAP center round box 60%>< | ||
- | ^ Mode ^ | + | ^ Mode ^ |
- | | 0 | | + | | 0 | |
- | | 1 | | + | | 1 | |
</ | </ | ||
- | * In the example, | + | * In the example, front-panel |
- | * To query the modulation source for CH 2, use [[slice: | + | * V< |
+ | * To query the signal delivered to the front-panel Output 1, use [[slice: | ||
---- | ---- | ||
+ | ==== Query Signal Delivered to Front-Panel Output 2: MODE2? ==== | ||
+ | |||
+ | < | ||
+ | Returns identity of signal delivered to front-panel Output 2 according to <tabref mode2?>. | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Response | ||
+ | | 0 | Front-panel Output 2 has no signal | ||
+ | | 513 | Front-panel Output 2 monitors CH 2 HV output | ||
+ | </ | ||
+ | |||
+ | * In the example, front-panel Output 2 is monitoring CH 2 output | ||
+ | * V< | ||
+ | * To set what signal is delivered to front-panel Output 2, use [[slice: | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ==== Set Signal Delivered to Front-Panel Output 2: MODE2 ==== | ||
+ | |||
+ | < | ||
+ | Returns MODE2? | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Mode ^ Result | ||
+ | | 0 | Sets signal at front-panel Output 2 to no signal | ||
+ | | 1 | Sets signal at front-panel Output 2 to monitor CH 2 Output | ||
+ | </ | ||
+ | |||
+ | * In the example, front-panel Output 2 will henceforth monitor the CH 2 output | ||
+ | * V< | ||
+ | * To query the signal delivered to the front-panel Output 2, use [[slice: | ||
+ | |||
+ | ---- | ||
slice/dhv/api.txt · Last modified: 2023/12/06 20:39 by Christiana Sasser