Differences

This shows you the differences between two versions of the page.

--- slice:dcc [2020/11/10 18:55] – [Specifications] Michael Radunsky
+++ slice:dcc [2021/12/15 21:08] – external edit 127.0.0.1
@@ Line 15: / Line 15: @@
 Click here for the [[https://www.vescent.com/products/electronics/slice/slice-cc-dual-channel-current-controller/|SLICE-DCC web page]].\\
 Click here for the [[https://github.com/Vescent|Github page for SLICE-DCC GUI]]\\
-Click here for the [[https://github.com/Vescent/SLICE-DCC-Firmware-Upgrade|Github page for SLICE-DCC firmware revisions]]\\
+Click here for the [[https://github.com/Vescent/FFC_Firmware_Upgrade-and-FPGA-Software-Firmware|Github page for SLICE-DCC firmware revisions]]\\
 Please check back for added functionality.  Contact [[[email protected]|sales [at] vescent [dot] com]] for questions and corrections, or to request added functionality.
 ===== List of Warning Symbols =====
@@ Line 100: / Line 100: @@
 | \\ \\ Current Noise((Constant Current Mode)) ((rms 100 Hz to 1 MHz))  |  1.5\\ 4\\ 10\\ 15                      |
 | Current Modulation Input Impedance \\ Rear \\ Front  |  \\ >20 kΩ\\ 50 Ω or 1 MΩ  |
-| Modulation Bandwidth((-3 dB point)), ((front & rear modulation input ports))|  DC to >1 MHz                |
+|Modulation Bandwidth((-3 dB point)), ((front & rear modulation input ports))|  DC to >1 MHz                |
+| Modulation Input Range                                               |  ±10 V                                  |
 |Modulation Depth          \\ SLICE-DCC-200\\ SLICE-DCC-500\\ SLICE-DCC-1000\\ SLICE-DCC-2000 |  \\ ±10 mA\\ ±25 mA\\ ±50 mA\\ ±50 mA  |
 |Modulation Transfer Function  \\ SLICE-DCC-200\\ SLICE-DCC-500\\ SLICE-DCC-1000\\ SLICE-DCC-2000 |  \\ 1 mA/V \\ 2.5 mA/V \\ 5 mA/V \\ 5 mA/V  |
-| Modulation Input Range                                               |  ±10 V                                  |
+| Current Resolution \\ SLICE-DCC-200\\ SLICE-DCC-500\\ SLICE-DCC-1000\\ SLICE-DCC-2000 |  \\ 10 µA \\ 10 µA \\ 20 µA \\ 100 µA                                 |
-| Current Resolution                                                   |  100 µA                                 |
 | Drift                                                                |  <25 µA/°C                              |
 | Power Stability((constant power mode))                               |  0.1% rms((relative to maximum power))  |
@@ Line 356: / Line 356: @@
 ===== Serial API =====
 It is possible to control the SLICE-DCC through serial commands.  Click here to access the [[slice:dcc:API|SLICE-DCC API]].
+<WRAP round important 100%>
+Upgrading the SLICE-QTC firmware is not always necessary to use the Serial API. Check your installed firmware version in the settings menu against the most recent firmware version given [[https://github.com/Vescent/SLICE-DCC-Firmware-Upgrade|here]].
+</WRAP>
 Please contact [[[email protected]|sales [at] vescent [dot] com]] for information.