Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision |
| waveguide:manual [2016/03/02 22:13] – [Operation] Michael Radunsky | waveguide:manual [2016/03/02 22:24] – [Operation] Michael Radunsky |
|---|
| |
| =====Operation===== | =====Operation===== |
| The LS-105 is shipped with a 5 V power supply and a cable for connection to the SEEOR, as shown in <imgref pinout>. If you purchased a chip level SEEOR the cable will have a connector on one end and clip-connectors on the other end. If you purchased a fiber-coupled SEEOR the cable will be connectorized at both ends. | The LS-105 is shipped with a 5 V power supply and a cable for connection to the SEEOR, as shown in <imgref shipkit>. If you purchased a chip level SEEOR the cable will have a connector on one end and clip-connectors on the other end. If you purchased a fiber-coupled SEEOR the cable will be connectorized at both ends. |
| <WRAP right round box 300px><imgcaption shipkit| The LS-105, power supply, and connection cable. The figure above shows a cable for connecting to a chip-level SEEOR. For a fiber packaged device, the cable will have connectors on both ends.>{{:waveguide:manuals:2_ship_kit.png?250x}}</imgcaption></WRAP> | <WRAP left round box 300px><imgcaption shipkit| The LS-105, power supply, and connection cable. The figure above shows a cable for connecting to a chip-level SEEOR. For a fiber packaged device, the cable will have connectors on both ends.>{{:waveguide:manuals:2_ship_kit.png?250x}}</imgcaption></WRAP> |
| |
| <WRAP right round box 550px><imgcaption pinout| Pin-Out for the LC-105 connection to the optical head.>{{ :waveguide:manuals:3_pin_out.png?500}}</imgcaption></WRAP> | <WRAP right round box 550px><imgcaption pinout| Pin-Out for the LC-105 connection to the optical head.>{{ :waveguide:manuals:3_pin_out.png?500}}</imgcaption></WRAP> |
| | |
| The cable plugs into the LS-105 with a push connector (female bulkhed connector: [[http://www.digikey.com/product-detail/en/hirose-electric-co-ltd/HR10A-10R-10SB/HR359-ND/279920|Hirose HR10A-10R-10SB]]; male cable end: [[http://www.digikey.com/product-detail/en/hirose-electric-co-ltd/HR10A-10P-10P/HR116-ND/40909|Hirose HR10A-10P-10P]]). To remove the cable simply pull from the metal housing on the end of the connector. The connector pin-out is shown in <imgref shipkit>. The clip leads are labeled appropriately. | The cable plugs into the LS-105 with a push connector (female bulkhead connector: [[http://www.digikey.com/product-detail/en/hirose-electric-co-ltd/HR10A-10R-10SB/HR359-ND/279920|Hirose HR10A-10R-10SB]]; male cable end: [[http://www.digikey.com/product-detail/en/hirose-electric-co-ltd/HR10A-10P-10P/HR116-ND/40909|Hirose HR10A-10P-10P]]). To remove the cable simply pull from the metal housing on the end of the connector. The connector pin-out is shown in <imgref pinout>. The clip leads are labeled appropriately. |
| |
| ===Prototype EO Scanner Optical Head=== | ===Prototype EO Scanner Optical Head=== |
