User Tools

Site Tools


slice:quick_start_qt

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
slice:quick_start_qt [2019/05/02 18:00]
Michael Radunsky [Links]
slice:quick_start_qt [2019/05/17 12:43] (current)
Michael Radunsky
Line 1: Line 1:
-======SLICE-QT Four-Channel Temperature Controller Quick Start Guide ======+======SLICE-QTC Four-Channel Temperature Controller Quick Start Guide ======
  
-Model No. SLICE-QT+Model No. SLICE-QT AND SLICE-QTC
  
 Document Revision: 1 Document Revision: 1
Line 7: Line 7:
 Document Last Updated on ~~LASTMOD~~ Document Last Updated on ~~LASTMOD~~
  
-Please read [[:limited_warranty|Limited Warranty]] and [[:warnings_cautions|General Warnings and Cautions]] prior to operating the SLICE-QT.+Please read [[:limited_warranty|Limited Warranty]] and [[:warnings_cautions|General Warnings and Cautions]] prior to operating the SLICE-QTC.
  
 ====Links==== ====Links====
  
-Click here for the [[slice:qt|SLICE-QT Owner's Manual]]\\ +Click here for the [[slice:qt|SLICE-QTC Owner's Manual]]\\ 
-Click here for the [[slice:qt:API|SLICE-QT API]].\\+Click here for the [[slice:qt:API|SLICE-QTC API]].\\
 Click here for the [[slice:Z-N|Ziegler-Nichols loop tuning instructions]].\\ Click here for the [[slice:Z-N|Ziegler-Nichols loop tuning instructions]].\\
-Click here for the [[https://www.vescent.com/products/electronics/slice/slice-qt-four-channel-temperature-controller/|SLICE-QT]] web page.\\+Click here for the [[https://www.vescent.com/products/electronics/slice/slice-qt-four-channel-temperature-controller/|SLICE-QTC]] web page.\\
 Click here for the [[https://github.com/Vescent|Github page for SLICE-QTC GUI]]\\ Click here for the [[https://github.com/Vescent|Github page for SLICE-QTC GUI]]\\
 Click here for the [[https://github.com/Vescent/SLICE-QT-Firmware-Upgrade|Github page for SLICE-QTC firmware revisions]]\\ Click here for the [[https://github.com/Vescent/SLICE-QT-Firmware-Upgrade|Github page for SLICE-QTC firmware revisions]]\\
Line 22: Line 22:
 =====Description===== =====Description=====
  
-The SLICE-QT is a high-precision temperature controller (see <imgref qt_prod_shot>).  It will control up to four thermal plants with sub-millikelvin precision.+The SLICE-QTC is a high-precision temperature controller (see <imgref qt_prod_shot>).  It will control up to four thermal plants with sub-millikelvin precision.
  
-<imgcaption qt_prod_shot|The SLICE-QT>{{ slice:front-angle-acs-large.jpg?200|}}</imgcaption>+<imgcaption qt_prod_shot|The SLICE-QTC>{{ slice:front-angle-acs-large.jpg?200|}}</imgcaption>
  
 =====Purchase Includes===== =====Purchase Includes=====
-  * SLICE-QT Temperature Control Unit+  * SLICE-QTC Temperature Control Unit
   * AC power cord with appropriate wall plug for you location (if known)   * AC power cord with appropriate wall plug for you location (if known)
   * Four single-ended 6-ft control cables((More cables may be purchased separately))   * Four single-ended 6-ft control cables((More cables may be purchased separately))
Line 42: Line 42:
 When presented with a given view, it is possible to select the functionality or change the values in any field bordered in <color black/hsl(213, 80%, 60%)>blue</color> When a particular field is actively being edited, its border will be <color black/yellow>yellow</color> When presented with a given view, it is possible to select the functionality or change the values in any field bordered in <color black/hsl(213, 80%, 60%)>blue</color> When a particular field is actively being edited, its border will be <color black/yellow>yellow</color>
  
-  - Using <tabref pinout>, make connections from the SLICE-QT to your thermal plant via the cables supplied by Vescent.  Peel the shield back to make connections.  The shield is connected to the SLICE-QT case.  It is not recommended to connect the shield to the plant as ground loops may be formed, degrading performance. +  - Using <tabref pinout>, make connections from the SLICE-QTC to your thermal plant via the cables supplied by Vescent.  Peel the shield back to make connections.  The shield is connected to the SLICE-QTC case.  It is not recommended to connect the shield to the plant as ground loops may be formed, degrading performance. 
-  - Use the supplied AC power cord to provide power to the SLICE-QT.  The power converter inside the unit will accept any line voltage within the range in <tabref v_rng>+  - Use the supplied AC power cord to provide power to the SLICE-QTC.  The power converter inside the unit will accept any line voltage within the range in <tabref v_rng>
-  - Turn on the SLICE-QT with the power switch on the back of the unit located on the power entry module.+  - Turn on the SLICE-QTC with the power switch on the back of the unit located on the power entry module.
   - From the Home screen, touch the CH icon for the channel to be used to go to the Channel Detail screen.   - From the Home screen, touch the CH icon for the channel to be used to go to the Channel Detail screen.
   - Touch Settings > Load Limits   - Touch Settings > Load Limits
Line 66: Line 66:
   - Monitor on the performance screen to ensure system settles   - Monitor on the performance screen to ensure system settles
  
-| {{ :warning-sign.png?100&nolink }}  | Use caution grounding the shield at the transducer end of the interface cable as ground loops may be formed, degrading performance.                                        +| {{ :warning-sign.png?100&nolink }}  | Use caution grounding the shield (drain) at the transducer end of the interface cable as ground loops may be formed, degrading performance.  Consider floating the plant or not connecting the shield to the plant chassis.                                      
-| {{ :warning-sign.png?100&nolink }}  | WHEN USING A RESISTIVE HEATER, be sure to set the transducer type (CH X > Settings > Plant) to Heater/Monopolar.  If set to TEC/Bipolar, attempts by the SLICE-QT to actively cool your plant could result in a thermal runaway condition. |+| {{ :warning-sign.png?100&nolink }}  | WHEN USING A RESISTIVE HEATER, be sure to set the transducer type (CH X > Settings > Plant) to Heater/Monopolar.  If set to TEC/Bipolar, attempts by the SLICE-QTC to actively cool your plant could result in a thermal runaway condition. |
  
 <WRAP center round box 60%><tabcaption pinout |Cable pinout> <WRAP center round box 60%><tabcaption pinout |Cable pinout>
Line 78: Line 78:
 </tabcaption></WRAP> </tabcaption></WRAP>
  
-You may purchase more cables separately from Vescent Photonics.  We do not recommend making cables, but if you do so, make sure the metal sleeve (drain) is well connected to the chassis of the SLICE-QT.+You may purchase more cables separately from Vescent Photonics.  We do not recommend making cables, but if you do so, make sure the metal sleeve (drain) is well connected to the chassis of the SLICE-QTC.  Ground loops may form degrading performance if you connect the plant side of the drain to the plant chassis.  Consider floating the plant or not connecting the drain to the plant chassis.
  
-The SLICE-QT will accept input line voltages within the ranges in <tabref v_rng>.+The SLICE-QTC will accept input line voltages within the ranges in <tabref v_rng>.
 <WRAP center round box 60%><tabcaption v_rng |Input Voltage Specifications> <WRAP center round box 60%><tabcaption v_rng |Input Voltage Specifications>
 | **Parameter**       | **Value**  | **Units**  | | **Parameter**       | **Value**  | **Units**  |
Line 98: Line 98:
   - <color black/yellow>System locked range (yellow dashed lines)</color>   - <color black/yellow>System locked range (yellow dashed lines)</color>
  
-<imgcaption front|Front of rear of SLICE-QT>{{ :slice:slice-qt-front-numbered.png?534x221 |}}</imgcaption>+<imgcaption front|Front of rear of SLICE-QTC>{{ :slice:slice-qt-front-numbered.png?534x221 |}}</imgcaption>
 ===== Rear Panel ===== ===== Rear Panel =====
 The rear panel can be seen in <imgref back> The functions and connections are as follows: The rear panel can be seen in <imgref back> The functions and connections are as follows:
Line 106: Line 106:
   - Input trigger (BNC)   - Input trigger (BNC)
   - USB port (Type B)   - USB port (Type B)
-  - Connections to thermal plants(([[https://www.digikey.com/product-detail/en/cui-inc/PD-40S/CP-7240-ND/2119338|Four-pin DIN connector]]))((In some early versions of the SLICE-QT, the order of these connectors is reversed.))+  - Connections to thermal plants(([[https://www.digikey.com/product-detail/en/cui-inc/PD-40S/CP-7240-ND/2119338|Four-pin DIN connector]]))((In some early versions of the SLICE-QTC, the order of these connectors is reversed.))
  
-<imgcaption back|View of rear of SLICE-QT>{{ :slice:slice-qt-rear-numbered.png?534x221 |}}</imgcaption>\\+<imgcaption back|View of rear of SLICE-QTC>{{ :slice:slice-qt-rear-numbered.png?534x221 |}}</imgcaption>\\
  
 Contact [[sales@vescent.com|sales [at] vescent [dot] com]] for questions and corrections, or to request added functionality. Contact [[sales@vescent.com|sales [at] vescent [dot] com]] for questions and corrections, or to request added functionality.
slice/quick_start_qt.txt · Last modified: 2019/05/17 12:43 by Michael Radunsky