| Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision |
| slice:qt [2019/02/13 01:27] – [Front-panel Inputs & Outputs] Michael Radunsky | slice:qt [2019/02/16 02:19] – [SLICE-QT Four-Channel Temperature Controller] Michael Radunsky |
|---|
| Please read [[:limited_warranty|Limited Warranty]] and [[:warnings_cautions|General Warnings and Cautions]] prior to operating the SLICE-QT. | Please read [[:limited_warranty|Limited Warranty]] and [[:warnings_cautions|General Warnings and Cautions]] prior to operating the SLICE-QT. |
| |
| [[slice:quick_start_qt|SLICE-QT Quick Start Guide]]\\ | Click here for the [[slice:quick_start_qt|SLICE-QT Quick Start Guide]].\\ |
| [[https://www.vescent.com/products/electronics/slice/slice-qt-four-channel-temperature-controller/|SLICE-QT web page]]\\ | Click here for the [[slice:qt:API|SLICE-QT API]].\\ |
| | Click here for the [[https://www.vescent.com/products/electronics/slice/slice-qt-four-channel-temperature-controller/|SLICE-QT web page]].\\ |
| Please check back for added functionality. Contact [[[email protected]|sales [at] vescent [dot] com]] for questions and corrections, or to request added functionality. | Please check back for added functionality. Contact [[[email protected]|sales [at] vescent [dot] com]] for questions and corrections, or to request added functionality. |
| =====Description===== | =====Description===== |
| |
| === Output Channels 1 & 2 === | === Output Channels 1 & 2 === |
| Similarly, you can program the output signals for the Output Channels 1 and 2. For each channel, the actual (measured) temperature, the temperature error, or the current output can be chosen as the output signal. For instance, if you select <color magenta>Channel 1 Output</color> from <imgref io> you will be presented with <imgref out_prog>. You can choose any value from <tabref output> to be delivered to the <color magenta>Channel 1 Output</color> output on the front panel. Touch the Settings icon to the right of the channel selection to adjust the Gain and Offset for these output signals as in <imgref out_gain>. | Similarly, you can program the output signals for the Output Channels 1 and 2. For each channel, the actual (measured) temperature, the temperature error, or the current output can be chosen as the output signal. For instance, if you select <color magenta>Channel 1 Output</color> from <imgref io> you will be presented with <imgref out_prog>. You can choose any value from <tabref output> to be delivered to the <color magenta>Channel 1 Output</color> output on the front panel. Touch the Settings icon to the right of the channel selection to adjust the Gain and Offset for these output signals as in <imgref out_gain>. When porting the Temperature of a given loop to an Output, setting the Gain equal to 0.1 V/°C and the offset to 0 V will give a convenient 2 V output at 20°C. |
| |
| <imgcaption out_prog|Programming the output on Channel 1 Output>{{ :slice:slice-qt_program_output.jpg?400x254 |}}</imgcaption> | <imgcaption out_prog|Programming the output on Channel 1 Output>{{ :slice:slice-qt_program_output.jpg?400x254 |}}</imgcaption> |
| From time to time, Vescent will upgrade the firmware for controlling the SLICE-QT. The procedure to upgrade the firmware is given [[slice:qt:firmware|here]]. | From time to time, Vescent will upgrade the firmware for controlling the SLICE-QT. The procedure to upgrade the firmware is given [[slice:qt:firmware|here]]. |
| ===== Serial API ===== | ===== Serial API ===== |
| It is possible to control the SLICE-QT through serial commands. More information coming soon. Please contact [[[email protected]|sales [at] vescent [dot] com]] for information. | It is possible to control the SLICE-QT through serial commands. Click here to access the [[slice:qt:API|SLICE-QT API]]. |
| | |
| | More information coming soon. Please contact [[[email protected]|sales [at] vescent [dot] com]] for information. |
| |
| ===== Maintenance ===== | ===== Maintenance ===== |
