slice:dhv:api
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
slice:dhv:api [2020/05/26 23:49] – Michael Radunsky | slice:dhv:api [2020/05/27 00:47] – [Set Source of Modulation Signal for CH 2: MODEB] Michael Radunsky | ||
---|---|---|---|
Line 363: | Line 363: | ||
* In the example, CHANNEL 1 will henceforth respond to Trigger In. | * In the example, CHANNEL 1 will henceforth respond to Trigger In. | ||
- | * To query Error Code, use [[slice: | + | * To query response to trigger input, use [[slice: |
---- | ---- | ||
+ | ==== Query Trigger Out Meaning: TRIGOUT? ==== | ||
- | ==== Query Response | + | < |
+ | Returns the meaning of the Trigger Out signal with respect | ||
- | < | + | <WRAP center round box 60%>< |
- | Returns | + | ^ Response |
+ | | 0 | No change in state of the Trigger Out based state of CHANNEL | ||
+ | | 1 | The signal at Trigger Out will go high in sync with the ramp on CHANNEL | ||
+ | </ | ||
+ | |||
+ | * In the example, the signal at Trigger Out will go high in sync with the ramp on CH 1. | ||
+ | * To set the meaning of the Trigger Out signal, use [[slice: | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ==== Set Trigger Out: TRIGOUT ==== | ||
+ | |||
+ | < | ||
+ | Returns | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Selection | ||
+ | | 0 | Trigger out is unresponsive to state of CHANNEL | ||
+ | | 1 | A TTL high signal | ||
+ | </ | ||
+ | |||
+ | * In the example, Trigger Out will go high in sync with ramp on CH 1 | ||
+ | * To query Trigger Out meaning, use [[slice: | ||
+ | * Setting the Trigger Out to be in sync with CH 1 removes Trigger Out's synchronicity with CH 2 & vice versa | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ==== Query Source of Modulation Signal for CH 1: MODEA? ==== | ||
+ | |||
+ | < | ||
+ | Returns from where CH 1 receives modulation control | ||
- | <WRAP center round box 60%>< | + | <WRAP center round box 60%>< |
^ Response | ^ Response | ||
- | | 0 | | + | | 0 | |
- | | 1 | | + | | 257 | |
</ | </ | ||
- | * In the example, CH 1 will respond to a Trigger In signal. | + | * In the example, CH 1 accepts its modulation |
- | * To set the response to a Trigger In signal, use [[slice: | + | * To set from where CH 1 accepts |
+ | * Only one modulation source may be active at a time | ||
---- | ---- | ||
- | ==== Set Response to Trigger In: TRIGIN | + | ==== Set Source of Modulation Signal for CH 1: MODEA ==== |
- | < | + | < |
- | Returns | + | Returns |
- | <WRAP center round box 60%>< | + | <WRAP center round box 60%>< |
- | ^ | + | ^ |
- | | 0 | | + | | 0 | |
- | | 1 | | + | | 1 | |
</ | </ | ||
- | * In the example, | + | * In the example, |
- | * To query Error Code, use [[slice: | + | * To query the modulation source for CH 1, use [[slice: |
---- | ---- | ||
+ | |||
+ | ==== Query Source of Modulation Signal for CH 2: MODEB? ==== | ||
+ | |||
+ | < | ||
+ | Returns from where CH 2 receives modulation control as seen in <tabref modeb?>. | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Response | ||
+ | | 0 | CH 2 accepts its modulation signal from rear-panel SMA connector | ||
+ | | 257 | CH 2 accepts its modulation signal from front-panel Input B BNC connector | ||
+ | </ | ||
+ | |||
+ | * In the example, CH 2 accepts its modulation signal from the front-panel Input B. | ||
+ | * To set from where CH B accepts a modulation signal, use [[slice: | ||
+ | * Only one modulation source may be active at a time | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ==== Set Source of Modulation Signal for CH 2: MODEB ==== | ||
+ | |||
+ | < | ||
+ | Returns MODEB? | ||
+ | |||
+ | <WRAP center round box 60%>< | ||
+ | ^ Mode ^ Location of modulation input for CH 2 ^ | ||
+ | | 0 | CH 2 accepts modulation signal from rear-panel SMA connector | ||
+ | | 1 | CH 2 accepts modulation signal from front-panel Input B BNC connector | ||
+ | </ | ||
+ | |||
+ | * In the example, CH 2 will henceforth accept a modulation signal from the front-panel Input B BNC | ||
+ | * To query the modulation source for CH 2, use [[slice: | ||
+ | |||
+ | ---- | ||
slice/dhv/api.txt · Last modified: 2023/12/06 20:39 by Christiana Sasser