slice:dhv:api
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | |||
slice:dhv:api [2023/11/30 21:29] – external edit 127.0.0.1 | slice:dhv:api [2023/12/06 20:39] (current) – Christiana Sasser | ||
---|---|---|---|
Line 47: | Line 47: | ||
---- | ---- | ||
==== Obtain System Controller firmware version: # | ==== Obtain System Controller firmware version: # | ||
- | < | + | < |
Returns firmware version of System Controller. | Returns firmware version of System Controller. | ||
+ | /*Note: For the Return Question mark, we had to use a slightly different question mark image. This one: ?. Rather than this one: ?. */ | ||
---- | ---- | ||
==== Reset System to Factory default: _FACTORY ==== | ==== Reset System to Factory default: _FACTORY ==== | ||
Line 72: | Line 73: | ||
<WRAP center round important 100%> | <WRAP center round important 100%> | ||
- | < | + | < |
Returns SCPI device information. Running System Controller firmware version 1.74 and DHV firmware version 1.18. | Returns SCPI device information. Running System Controller firmware version 1.74 and DHV firmware version 1.18. | ||
---- | ---- | ||
Line 85: | Line 86: | ||
==== Query Output Voltage Maximum: VLIM? ==== | ==== Query Output Voltage Maximum: VLIM? ==== | ||
- | < | + | < |
Returns maximum output in Volts for CHANNEL. | Returns maximum output in Volts for CHANNEL. | ||
Line 106: | Line 107: | ||
==== Query Operation Mode: CONTROL? ==== | ==== Query Operation Mode: CONTROL? ==== | ||
- | < | + | < |
Returns the enumerated modulation mode and status for CHANNEL. | Returns the enumerated modulation mode and status for CHANNEL. | ||
Where: \\ | Where: \\ | ||
Line 141: | Line 142: | ||
==== Query DC Bias: DCBIASV? ==== | ==== Query DC Bias: DCBIASV? ==== | ||
- | < | + | < |
Returns V< | Returns V< | ||
Line 164: | Line 165: | ||
==== Query Output Voltage: OUTVOLT? ==== | ==== Query Output Voltage: OUTVOLT? ==== | ||
- | < | + | < |
Returns V< | Returns V< | ||
Line 174: | Line 175: | ||
==== Query Range of Voltage Sweep: RANGEV? ==== | ==== Query Range of Voltage Sweep: RANGEV? ==== | ||
- | < | + | < |
Returns Range of the Sweep in Volts for CHANNEL. | Returns Range of the Sweep in Volts for CHANNEL. | ||
Line 198: | Line 199: | ||
==== Query Repetition Rate of Voltage Sweep: SWEEPRT? ==== | ==== Query Repetition Rate of Voltage Sweep: SWEEPRT? ==== | ||
- | < | + | < |
Returns Repetition Rate of the Sweep in Hertz for CHANNEL. | Returns Repetition Rate of the Sweep in Hertz for CHANNEL. | ||
Line 219: | Line 220: | ||
==== Query Sweep Mode: SWEEPMD? ==== | ==== Query Sweep Mode: SWEEPMD? ==== | ||
- | < | + | < |
Returns the enumerated Current Sweep Mode for CHANNEL. | Returns the enumerated Current Sweep Mode for CHANNEL. | ||
Line 251: | Line 252: | ||
==== Query Repetition Rate of Voltage Sweep: SWEEPRT? ==== | ==== Query Repetition Rate of Voltage Sweep: SWEEPRT? ==== | ||
- | < | + | < |
Returns Repetition Rate of the Sweep in Hertz for CHANNEL. | Returns Repetition Rate of the Sweep in Hertz for CHANNEL. | ||
Line 272: | Line 273: | ||
==== Query Sweep Mode: SWEEPMD? ==== | ==== Query Sweep Mode: SWEEPMD? ==== | ||
- | < | + | < |
Returns the enumerated Current Sweep Mode for CHANNEL. | Returns the enumerated Current Sweep Mode for CHANNEL. | ||
Line 304: | Line 305: | ||
==== Query Error Code: ERROR? ==== | ==== Query Error Code: ERROR? ==== | ||
- | < | + | < |
Returns the Error Code for CHANNEL. | Returns the Error Code for CHANNEL. | ||
Line 336: | Line 337: | ||
==== Query Response to Trigger In: TRIGIN? ==== | ==== Query Response to Trigger In: TRIGIN? ==== | ||
- | < | + | < |
Returns the effect of Trigger In signal on CHANNEL as seen in <tabref trigin?> | Returns the effect of Trigger In signal on CHANNEL as seen in <tabref trigin?> | ||
Line 368: | Line 369: | ||
==== Query Trigger Out Meaning: TRIGOUT? ==== | ==== Query Trigger Out Meaning: TRIGOUT? ==== | ||
- | < | + | < |
Returns the meaning of the Trigger Out signal with respect to CHANNEL as seen in <tabref trigout?> | Returns the meaning of the Trigger Out signal with respect to CHANNEL as seen in <tabref trigout?> | ||
Line 401: | Line 402: | ||
==== Query Source of Modulation Signal for CH 1: MODEA? ==== | ==== Query Source of Modulation Signal for CH 1: MODEA? ==== | ||
- | < | + | < |
Returns from where CH 1 receives modulation control as seen in <tabref modea?>. | Returns from where CH 1 receives modulation control as seen in <tabref modea?>. | ||
Line 434: | Line 435: | ||
==== Query Source of Modulation Signal for CH 2: MODEB? ==== | ==== Query Source of Modulation Signal for CH 2: MODEB? ==== | ||
- | < | + | < |
Returns from where CH 2 receives modulation control as seen in <tabref modeb?>. | Returns from where CH 2 receives modulation control as seen in <tabref modeb?>. | ||
Line 467: | Line 468: | ||
==== Query Signal Delivered to Front-Panel Output 1: MODE1? ==== | ==== Query Signal Delivered to Front-Panel Output 1: MODE1? ==== | ||
- | < | + | < |
Returns identity of signal delivered to front-panel Output 1 according to <tabref mode1?>. | Returns identity of signal delivered to front-panel Output 1 according to <tabref mode1?>. | ||
Line 501: | Line 502: | ||
==== Query Signal Delivered to Front-Panel Output 2: MODE2? ==== | ==== Query Signal Delivered to Front-Panel Output 2: MODE2? ==== | ||
- | < | + | < |
Returns identity of signal delivered to front-panel Output 2 according to <tabref mode2?>. | Returns identity of signal delivered to front-panel Output 2 according to <tabref mode2?>. | ||
slice/dhv/api.txt · Last modified: 2023/12/06 20:39 by Christiana Sasser