| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision |
| ice:servo-peaklock [2016/05/09 20:31] – [Specifications] Michael Radunsky | ice:servo-peaklock [2019/12/20 18:20] – [Specifications] Michael Radunsky |
|---|
| |
| Please read [[:limited_warranty|Limited Warranty]] and [[:warnings_cautions|General Warnings and Cautions]] prior to operating the ICE-CS1. | Please read [[:limited_warranty|Limited Warranty]] and [[:warnings_cautions|General Warnings and Cautions]] prior to operating the ICE-CS1. |
| | |
| | [[http://www.vescent.com/products/electronics/icetm-integrated-control-electronics/ice-cs1-current-control-and-frequency-servo-board/|ICE-CS1 web page.]] |
| |
| ===== Description ===== | ===== Description ===== |
| ^ ^ ICE-CS1-200 ^ ICE-CS1-500 ^ Units ^ | ^ ^ ICE-CS1-200 ^ ICE-CS1-500 ^ Units ^ |
| ^ Current Source ^ ^ ^ ^ | ^ Current Source ^ ^ ^ ^ |
| |<html> </html>Current range| 0-200 | 0-500 | mA | | |Current range| 0-200 | 0-500 | mA | |
| |<html> </html>Current setpoint resolution | 200 | 500 | μA | | |Current setpoint resolution | 200 | 500 | μA | |
| |<html> </html>Current noise density((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| <100 | <200 | pA / <HTML> √<span style="text-decoration: overline;">Hz</span> </HTML> | | |Current noise density((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| <100 | <200 | pA /√Hz | |
| |<html> </html>RMS Noise (10Hz - 100kHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| <50 | <100 | nA | | |RMS Noise (10Hz - 100kHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| <50 | <100 | nA | |
| |<html> </html>RMS Noise (10Hz - 1MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| <100 | <150 | nA | | |RMS Noise (10Hz - 1MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| <100 | <150 | nA | |
| |<html> </html>RMS Noise (10Hz - 10MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| <300 | <500 | nA | | |RMS Noise (10Hz - 10MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))| <300 | <500 | nA | |
| |<html> </html>Absolute accuracy| 2 || % | | |Absolute accuracy| 2 || % | |
| ^ Peak Lock Servo ^ ^^ ^ | ^ Peak Lock Servo ^ ^^ ^ |
| |<html> </html>Bandwidth((Calculated based on RF dither frequency of 4 MHz which limits servo bandwidth))| 3 || MHz | | |Bandwidth((Calculated based on RF dither frequency of 4 MHz which limits servo bandwidth))| 3 || MHz | |
| |<html> </html>Input Voltage Range | ±1 || V | | |Input Voltage Range | ±1 || V | |
| |<html> </html>Dither Frequency | 4 || MHz | | |Dither Frequency | 4 || MHz | |
| |<html> </html>Phase Shift Resolution | 5.6 || deg | | |Phase Shift Resolution | 5.6 || deg | |
| |<html> </html>Input Voltage Noise(( Referenced to 50Ω load)) | TBD || nV/ <HTML> √<span style="text-decoration: overline;">Hz</span> </HTML> | | |Input Voltage Noise(( Referenced to 50Ω load)) | TBD || nV/√Hz | |
| ^ Loop Filter Parameters ^ ^^ ^ | ^ Loop Filter Parameters ^ ^^ ^ |
| |<html> </html>Proportional Gain (ref to DC Error) | -22 to +20 || dB | | |Proportional Gain (ref to DC Error) | -22 to +20 || dB | |
| |<html> </html>Proportional Gain Resolution | 2 || dB | | |Proportional Gain Resolution | 2 || dB | |
| |<html> </html>Integrator| 3, 10, 30, 100, 300 || kHz | | |Integrator| 3, 10, 30, 100, 300 || kHz | |
| |<html> </html>Differential| Off, Fixed at 3 times integrator pole || | | |Differential| Off, Fixed at 3 times integrator pole || | |
| |<html> </html>Differential Gain | 18 || dB | | |Differential Gain | 18 || dB | |
| |
| ^Electrical Specifications^^^^^ | ^Electrical Specifications^^^^^ |
