User Tools

Site Tools


ice:servo-opls

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
ice:servo-opls [2019/11/18 23:31] – [Calculating Phase Noise] Michael Radunskyice:servo-opls [2019/11/18 23:34] – [Specifications] Michael Radunsky
Line 30: Line 30:
 | Current range                                                                                                                                                0-200                                                                                            0-500        |  mA      | | Current range                                                                                                                                                0-200                                                                                            0-500        |  mA      |
 | Current setpoint resolution                                                                                                                                  200                                                                                              500          |  μA      | | Current setpoint resolution                                                                                                                                  200                                                                                              500          |  μA      |
-| Current noise density((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))                               |  <100                                                                                            |  <200         | pA /√Hz +| Current noise density                                <100                                                                                            |  <200         | pA /√Hz 
-| RMS Noise (10Hz - 100kHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))                           |  <50                                                                                              <100          nA      | +| RMS Noise (10Hz - 100kHz)              |  <50                                                                                              <100          nA      | 
-| RMS Noise (10Hz - 1MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))                             |  <100                                                                                            |  <150          nA      | +| RMS Noise (10Hz - 1MHz)                  |  <100                                                                                            |  <150          nA      | 
-| RMS Noise (10Hz - 10MHz)((All measurements guaranteed on design and verified experimentally on D2-105 which uses same circuit.))                            |  <300                                                                                            |  <500          nA      |+| RMS Noise (10Hz - 10MHz)                |  <300                                                                                            |  <500          nA      |
 | Absolute accuracy                                                                                                                                            2                                                                                                              ||  %       | | Absolute accuracy                                                                                                                                            2                                                                                                              ||  %       |
 ^ Offset Phase Lock Servo Input Signal                                                                                                                        ^                                                                                                                 |^          ^ ^ Offset Phase Lock Servo Input Signal                                                                                                                        ^                                                                                                                 |^          ^
Line 90: Line 90:
  
  
-The charge pump in the OPLS outputs a signal proportional to the phase-error and the transfer function is as shown in <imgref xferfunc> However, the OPLS will typically be used to control a //frequency//-tunable device (such as a laser). In this configuration, the effective loop filter is not the one shown in <imgref opls_side_panel>, but includes a extra integration corresponding to converting the phase-error input to a frequency error. Thus, ω<sub> </sub>sets the frequency transition from single-integration to double-integration and ω<sub>I </sub> from single-integration to proportional feedback. It is important to understand this 'hidden' integrator when configuring the loop filter parameters. +The charge pump in the OPLS outputs a signal proportional to the phase-error and the transfer function is as shown in <imgref xferfunc> However, the OPLS will typically be used to control a //frequency//-tunable device (such as a laser). In this configuration, the effective loop filter is not the one shown in <imgref xferfunc>, but includes a extra integration corresponding to converting the phase-error input to a frequency error. Thus, ω<sub> </sub>sets the frequency transition from single-integration to double-integration and ω<sub>I </sub> from single-integration to proportional feedback. It is important to understand this 'hidden' integrator when configuring the loop filter parameters. 
  
 =====Calculating Phase Noise ===== =====Calculating Phase Noise =====
ice/servo-opls.txt · Last modified: 2021/08/26 15:26 by 127.0.0.1