User Tools

Site Tools


ice:oem_integration

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
ice:oem_integration [2020/03/06 01:53] – [I2C Addressing] Michael Radunskyice:oem_integration [2021/08/26 15:26] (current) – external edit 127.0.0.1
Line 32: Line 32:
 </WRAP> </WRAP>
  
-Power can be provided directly to the internal power bus headers if no master controller is used in the system, but this is highly discouraged as the power requirements are much more strict in order to prevent damaging system components. There are three power bus connectors shown in <imgref pcbSchematic> that utilize 0.1 inch double row board to board headers. The 6x2 headers ([[http://cloud.samtec.com/catalog_english/ESQ_TH.PDF|Samtec PN: ESQ-106-13-T-D]]) on either side of the pcb  carry 5V_A, +15V, +12V, -12V, -15V power rails and GND_A and GND signal. Both of the headers must be powered by the same power rails and be connected to the same grounds. The signal name GND_A is the return current path for the 5V_A rail which provides high current to daughter modules which require it (such as the [[ice:quadtemp|ICE-QT1]]). The 4x2 header ([[http://cloud.samtec.com/catalog_english/ESQ_TH.PDF|Samtec PN: ESQ-104-13-T-D]]) in the center of the pcb carries the digital communications bus and +5V_D power rail. The 5V_D power rail is designed to provide power to noisier digital components without contaminating the other analog power rails. This power rail can be "starred" off of the 5V_A line. All ground connections (GND, GND_A, GND_D) are intended to be starred at the power supply. The power sequence for turning on and off each voltage rail must be followed as described in the [[ice:oem_integration#power_sequencing|power sequencing section]] or damage will occur.+Power can be provided directly to the internal power bus headers if no master controller is used in the system, but this is highly discouraged as the power requirements are much more strict in order to prevent damaging system components. There are three power bus connectors shown in <imgref pcbSchematic> that utilize 0.1 inch double row board to board headers. The 6x2 headers ([[http://cloud.samtec.com/catalog_english/ESQ_TH.PDF|Samtec PN: ESQ-106-13-T-D]]) on either side of the PCB  carry 5V_A, +15V, +12V, -12V, -15V power rails and GND_A and GND signal. Both of the headers must be powered by the same power rails and be connected to the same grounds. The signal name GND_A is the return current path for the 5V_A rail which provides high current to daughter modules which require it (such as the [[ice:quadtemp|ICE-QT1]]). The 4x2 header ([[http://cloud.samtec.com/catalog_english/ESQ_TH.PDF|Samtec PN: ESQ-104-13-T-D]]) in the center of the PCB carries the digital communications bus and +5V_D power rail. The 5V_D power rail is designed to provide power to noisier digital components without contaminating the other analog power rails. This power rail can be "starred" off of the 5V_A line. All ground connections (GND, GND_A, GND_D) are intended to be starred at the power supply. The power sequence for turning on and off each voltage rail must be followed as described in the [[ice:oem_integration#power_sequencing|power sequencing section]] or damage will occur.
 ==== Power Draw by Module ==== ==== Power Draw by Module ====
 The power supply capacity for the supply used to power the ICE stack must be sized appropriately to handle expected power draw for the modules selected. Current draw is listed in the specifications for each of the daughter modules. The typical values indicate the quiescent current draw, and the max values represent worst case power draw depending on the functionality of the board. For example, the [[ice:quadtemp|ICE-QT1]] quad temperature controller has a maximum expected current draw on the 5V_A rail that depends on the maximum current supplied to thermo-electric coolers (TEC's). The maximum current here depends on what the user sets the current limit to for each temperature controller section. The max spec given is based on the highest current limit being set for each section, and the power supply should be capable of supply that current unless those current limits are set lower. Another example are the [[ice:servo-peaklock|ICE-CS1]] and [[ice:servo-opls|ICE-CP1]] modules, both of which include a laser current controller. The current draw on the +15V depends on the laser current output, which has a maximum output current that can be used to determine total current draw. This is detailed in the specifications charts on the respective product pages for all these modules. The power supply capacity for the supply used to power the ICE stack must be sized appropriately to handle expected power draw for the modules selected. Current draw is listed in the specifications for each of the daughter modules. The typical values indicate the quiescent current draw, and the max values represent worst case power draw depending on the functionality of the board. For example, the [[ice:quadtemp|ICE-QT1]] quad temperature controller has a maximum expected current draw on the 5V_A rail that depends on the maximum current supplied to thermo-electric coolers (TEC's). The maximum current here depends on what the user sets the current limit to for each temperature controller section. The max spec given is based on the highest current limit being set for each section, and the power supply should be capable of supply that current unless those current limits are set lower. Another example are the [[ice:servo-peaklock|ICE-CS1]] and [[ice:servo-opls|ICE-CP1]] modules, both of which include a laser current controller. The current draw on the +15V depends on the laser current output, which has a maximum output current that can be used to determine total current draw. This is detailed in the specifications charts on the respective product pages for all these modules.
Line 148: Line 148:
  
 <WRAP center round info 60%> <WRAP center round info 60%>
-Generally, the minimum bend radius for flat flex jumper cables is 2mm. The length of the stiffener behind the exposed contacts on the cable will determine how far out from the FFC pcb connector the first bend of the flat flex cable can occur. The clearance for this bend must be accounted for when designing an enclosure for the ICE boards. For example, with Molex brand flat flex cables, there needs to be a minimum 0.25 inch clearance from the front of the flat flex pcb connector to allow the cable to bend. Verify against the data sheet of the chosen flat flex jumper cable.+Generally, the minimum bend radius for flat flex jumper cables is 2mm. The length of the stiffener behind the exposed contacts on the cable will determine how far out from the FFC PCB connector the first bend of the flat flex cable can occur. The clearance for this bend must be accounted for when designing an enclosure for the ICE boards. For example, with Molex brand flat flex cables, there needs to be a minimum 0.25 inch clearance from the front of the flat flex PCB connector to allow the cable to bend. Verify against the data sheet of the chosen flat flex jumper cable.
 </WRAP> </WRAP>
  
ice/oem_integration.1583459587.txt.gz · Last modified: 2021/08/26 14:26 (external edit)