Product Manuals

User Tools

Site Tools

You are here: manuals » ice » master
ice:master

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
ice:master [2014/07/03 18:02] – [Specifications] jtshugrueice:master [2014/07/03 18:05] – [I/O] jtshugrue
Line 23: Line 23:
 ===== Specifications  ===== ===== Specifications  =====
 ^ ^  Min  ^  Typ  ^  Max  ^  Units  ^ ^ ^  Min  ^  Typ  ^  Max  ^  Units  ^
-^ Input Power Requirements((Minimum recommended supply current depends on configuration and number of daughter boards.))^+^ Input Power Requirements((Minimum recommended supply current depends on configuration and number of daughter boards.))^^^^^
 |5V Supply Current|  5  |  -  |  -  |  A  | |5V Supply Current|  5  |  -  |  -  |  A  |
 |15V Supply Current|  1.5  |  -  |  -  |  A  | |15V Supply Current|  1.5  |  -  |  -  |  A  |
Line 30: Line 30:
 |15V Line Input Range|  14.5  |  -  |  16  |  V  | |15V Line Input Range|  14.5  |  -  |  16  |  V  |
 |-15V Line Input Range|  -14.5  |  -  |  -16  |  V  | |-15V Line Input Range|  -14.5  |  -  |  -16  |  V  |
-^ Maximum Power Consumption((External power provided must also be able to handle the current requirements to utilize maximum power consumption specification)) ^ ^ ^+^ Maximum Power Consumption((External power provided must also be able to handle the current requirements to utilize maximum power consumption specification)) ^^^^^
 |5V Current Draw|  -  |  -  |  10  |  A  | |5V Current Draw|  -  |  -  |  10  |  A  |
 |15V Current Draw|  -  |  -  |  3  |  A  | |15V Current Draw|  -  |  -  |  3  |  A  |
 |-15V Current Draw|  -  |  -  |  3  |  A  | |-15V Current Draw|  -  |  -  |  3  |  A  |
-^ D-Sub 9pin Signals ^+^ D-Sub 9pin Signals ^^^^^
 |Safety Interlock Input Voltage Range|  0  |  -  |  3.3  |  V  | |Safety Interlock Input Voltage Range|  0  |  -  |  3.3  |  V  |
 |TXO Serial Input Voltage Range|  0  |  -  |  3.3  |  V  | |TXO Serial Input Voltage Range|  0  |  -  |  3.3  |  V  |
Line 42: Line 42:
 |5V Input Voltage Range|  4  |  5  |  9  |  V  | |5V Input Voltage Range|  4  |  5  |  9  |  V  |
 |5V Input Current Draw|  -  |  25  |  40  |  mA  | |5V Input Current Draw|  -  |  25  |  40  |  mA  |
-^ Slave Boards ^ ^ ^+^ Slave Boards ^^^^^
 |Max Number of Slave Boards |  -  |  -  |  8  | | |Max Number of Slave Boards |  -  |  -  |  8  | |
-^ Communication Methods ^ ^ ^+^ Communication Methods ^^^^^
 |I2C Bus |   | | |I2C Bus |   | |
 |TTL Serial (3.3V) |   | | |TTL Serial (3.3V) |   | |
Line 75: Line 75:
 Communication with the Master Controller and daughter modules is done through flat flex connecter J11. This connector contains two serial UART bi-directional communication busses, event system GPIO pins, and a safety interlock signal.  Communication with the Master Controller and daughter modules is done through flat flex connecter J11. This connector contains two serial UART bi-directional communication busses, event system GPIO pins, and a safety interlock signal. 
 J11 is a 12-pin 1.00mm pitch flat flex connector (FCI SFW12R-1STE1LF) with a pin definition shown in <tabref backpanelffc>. J11 is a 12-pin 1.00mm pitch flat flex connector (FCI SFW12R-1STE1LF) with a pin definition shown in <tabref backpanelffc>.
 +
 +<WRAP>
 <tabcaption backpanelffc| Pin definitions for J11> <tabcaption backpanelffc| Pin definitions for J11>
 ^  **Pin**  ^  **Signal**  ^ ^  **Pin**  ^  **Signal**  ^
Line 90: Line 92:
 |  12  |  Safety Interlock  | |  12  |  Safety Interlock  |
 </tabcaption> </tabcaption>
 +</WRAP>
 +
  
 == Serial UART == == Serial UART ==
ice/master.txt · Last modified: 2021/08/26 15:26 by 127.0.0.1