Product Manuals

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== DC1 Command Set ======

List of commands for the ICE DC1

<function=ICEfunc?0=Laser？?&1=I:CHANNEL:1&2=On&3=16>
Returns the status (on or off) of the current controller for the channel CHANNEL specified. CHANNEL can be either 1 or 2.
/*Note: For the Return Question mark, we had to use a slightly different question mark image. This one: ？. Rather than this one: ?. */

<function=ICEfunc?0=Laser&1=I:CHANNEL:1;A:On/Off:On&2=On&3=17>
Turns the current on or off to channel CHANNEL. Returns the output of the command **LASER?** command.

<function=ICEfunc?0=CurrSet？?&1=I:CHANNEL:1&2=97.6&3=18>
Returns the current setpoint (in mA) for channel CHANNEL.

<function=ICEfunc?0=CurrSet&1=I:CHANNEL:1;F:CURRENT:80.12&2=80.1&3=19>
Sets the current for the channel CHANNEL. Returns the output of the command **CURRSET** command.

<function=ICEfunc?0=CurrLim？?&1=I:CHANNEL:1&2=120&3=20>
Returns the current limit (in mA) for channel CHANNEL.

<function=ICEfunc?0=CurrLim&1=I:CHANNEL:1;F:CURRENT:130&2=130&3=21>
Sets the current limit for the channel CHANNEL. Returns the output of the command **CURRLIM** command.

<function=ICEfunc?0=ServoEn？?&1=I:CHANNEL:1&2=On&3=22>
Returns the status (on or off) of enabling the analog current modulation input for servoing the laser current for the channel CHANNEL specified. CHANNEL can be either 1 or 2.

<function=ICEfunc?0=ServoEn&1=I:CHANNEL:1;A:On/Off:On&2=On&3=23>
Turns the analog current modulation input on or off to channel CHANNEL. Returns the output of the command **SERVOEN?** command.

<function=ICEfunc?0=EvtData？?&1=I:CHANNEL:1;I:ROW:3&2=67.34&3=25>
Returns the current setting in the Event Jump Table for channel CHANNEL and row ROW. 

<function=ICEfunc?0=EvtData&1=I:CHANNEL:1;I:ROW:3;F:CURRENT:78.12&2=78.1&3=26>
Sets the current to CURRENT in in the event table for row ROW and channel CHANNEL.

<function=ICEfunc?0=EvtNum?&1=I:CHANNEL:1&2=7&3=27>
Reads the number of jump rows to loop through for channel CHANNEL in the jump event system. Range from 2 - 8. If set to 4, then the sequence of jump rows will be 1,2,3,4,1,2,3,4,1... where the numbers correspond to the **ROW** set when loading data in with the EvtData command.

<function=ICEfunc?0=EvtNum&1=I:CHANNEL:1;I:NUMBER:5&2=5&3=28>
Sets the number of jump rows to loop through for channel CHANNEL in the jump event system. Range from 2 - 8. If set to 4, then the sequence of jump rows will be 1,2,3,4,1,2,3,4,1... where the numbers correspond to the **ROW** set when loading data in with the EvtData command.

<function=ICEfunc?0=EvtJRow？?&1=I:CHANNEL:1&2=3&3=29>
Returns the next row that the will be read from the Event Jump Table when the device gets an event matching the event set with the **EvtJUMP** command for channel CHANNEL. 

<function=ICEfunc?0=EvtJRow&1=I:CHANNEL:1;I:NEXT:3&2=3&3=30>
Sets the next row that the will be read from the Event Jump Table when the device gets an event matching the event set with the **EvtJUMP** command for channel CHANNEL. 

<function=ICEfunc?0=EvtJump?&1=I:CHANNEL:1&2=6&3=31>
Reads the event address that channel CHANNEL lists to for jumping the laser current. Address range is 0-7 where address 0 is no event. 

<function=ICEfunc?0=EvtJump&1=I:CHANNEL:1;I:ADDRESS:5&2=5&3=32>
Sets the event address that channel CHANNEL lists to for jumping the laser current. Address range is 0-7 where address 0 is no event. 


<function=ICEfunc?0=EvtLOff?&1=I:CHANNEL:1&2=4&3=33>
Reads the event address for turning the laser off on channel CHANNEL. Address range is 0-7 where address 0 is no event. 

<function=ICEfunc?0=EvtLOff?&1=I:CHANNEL:1;I:ADDRESS:2&2=2&3=34>
Sets the event address for turning the laser off on channel CHANNEL. Address range is 0-7 where address 0 is no event. 

<function=ICEfunc?0=Pulse？?&1=I:CHANNEL:1&2=On&3=35>
Returns the state of the laser pulse (whether shunting current away from laser or not) on channel CHANNEL.

<function=ICEfunc?0=Pulse&1=I:CHANNEL:1;A:STATE:Off&2=Off&3=36>
Sets the state of the laser pulse (whether shunting current away from laser or not) on channel CHANNEL.