Differences

This shows you the differences between two versions of the page.

--- ice:dual-current:ice-dc1_-_dual_current_controller [2023/11/30 21:29] – external edit 127.0.0.1
+++ ice:dual-current:ice-dc1_-_dual_current_controller [2023/12/06 20:40] (current) – Christiana Sasser
@@ Line 3: / Line 3: @@
 List of commands for the ICE DC1
-<function=ICEfunc?0=Laser?&1=I:CHANNEL:1&2=On&3=16>
+<function=ICEfunc?0=Laser？?&1=I:CHANNEL:1&2=On&3=16>
 Returns the status (on or off) of the current controller for the channel CHANNEL specified. CHANNEL can be either 1 or 2.
+/*Note: For the Return Question mark, we had to use a slightly different question mark image. This one: ？. Rather than this one: ?. */
 <function=ICEfunc?0=Laser&1=I:CHANNEL:1;A:On/Off:On&2=On&3=17>
 Turns the current on or off to channel CHANNEL. Returns the output of the command **LASER?** command.
-<function=ICEfunc?0=CurrSet?&1=I:CHANNEL:1&2=97.6&3=18>
+<function=ICEfunc?0=CurrSet？?&1=I:CHANNEL:1&2=97.6&3=18>
 Returns the current setpoint (in mA) for channel CHANNEL.
@@ Line 15: / Line 16: @@
 Sets the current for the channel CHANNEL. Returns the output of the command **CURRSET** command.
-<function=ICEfunc?0=CurrLim?&1=I:CHANNEL:1&2=120&3=20>
+<function=ICEfunc?0=CurrLim？?&1=I:CHANNEL:1&2=120&3=20>
 Returns the current limit (in mA) for channel CHANNEL.
@@ Line 21: / Line 22: @@
 Sets the current limit for the channel CHANNEL. Returns the output of the command **CURRLIM** command.
-<function=ICEfunc?0=ServoEn?&1=I:CHANNEL:1&2=On&3=22>
+<function=ICEfunc?0=ServoEn？?&1=I:CHANNEL:1&2=On&3=22>
 Returns the status (on or off) of enabling the analog current modulation input for servoing the laser current for the channel CHANNEL specified. CHANNEL can be either 1 or 2.
@@ Line 27: / Line 28: @@
 Turns the analog current modulation input on or off to channel CHANNEL. Returns the output of the command **SERVOEN?** command.
-<function=ICEfunc?0=EvtData?&1=I:CHANNEL:1;I:ROW:3&2=67.34&3=25>
+<function=ICEfunc?0=EvtData？?&1=I:CHANNEL:1;I:ROW:3&2=67.34&3=25>
 Returns the current setting in the Event Jump Table for channel CHANNEL and row ROW.
@@ Line 39: / Line 40: @@
 Sets the number of jump rows to loop through for channel CHANNEL in the jump event system. Range from 2 - 8. If set to 4, then the sequence of jump rows will be 1,2,3,4,1,2,3,4,1... where the numbers correspond to the **ROW** set when loading data in with the EvtData command.
-<function=ICEfunc?0=EvtJRow?&1=I:CHANNEL:1&2=3&3=29>
+<function=ICEfunc?0=EvtJRow？?&1=I:CHANNEL:1&2=3&3=29>
 Returns the next row that the will be read from the Event Jump Table when the device gets an event matching the event set with the **EvtJUMP** command for channel CHANNEL.
@@ Line 58: / Line 59: @@
 Sets the event address for turning the laser off on channel CHANNEL. Address range is 0-7 where address 0 is no event.
-<function=ICEfunc?0=Pulse?&1=I:CHANNEL:1&2=On&3=35>
+<function=ICEfunc?0=Pulse？?&1=I:CHANNEL:1&2=On&3=35>
 Returns the state of the laser pulse (whether shunting current away from laser or not) on channel CHANNEL.