| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| ice:commands:servo [2017/10/27 17:49] – Michael Radunsky | ice:commands:servo [2023/12/06 20:44] (current) – Christiana Sasser |
|---|
| |
| |
| <function=ICEfunc|0=PHASE?&2=58&3=TBD> | <function=ICEfunc?0=PHASE？&2=58&3=TBD> |
| Returns the phase shift (in degrees) on the dither signal modulating the laser current.((Not implemented as of November, 2017)) | Returns the phase shift (in degrees) on the dither signal modulating the laser current.((Not implemented as of November, 2017)) |
| <html></div></html> | <html></div></html> |
| | /*Note: For the Return Question mark, we had to use a slightly different question mark image. This one: ？. Rather than this one: ?. */ |
| |
| <function=ICEfunc|0=PHASE&1=F:PHASE:23&2=22.5&3=TBD> | <function=ICEfunc?0=PHASE&1=F:PHASE:23&2=22.5&3=TBD> |
| Sets the phase shift to PHASE (in degrees) on the dither signal modulating the laser current. Returns the output of the command **Phase?**((Not implemented as of November, 2017)) | Sets the phase shift to PHASE (in degrees) on the dither signal modulating the laser current. Returns the output of the command **Phase?**((Not implemented as of November, 2017)) |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=DitherA?&2=32&3=TBD> | <function=ICEfunc?0=DitherA？&2=32&3=TBD> |
| Returns the amplitude of the dither on the laser current. Output is integer from 0-255.((Not implemented as of November, 2017)) | Returns the amplitude of the dither on the laser current. Output is integer from 0-255.((Not implemented as of November, 2017)) |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=DitherA&1=I:AMP:35;&2=35&3=TBD> | <function=ICEfunc?0=DitherA&1=I:AMP:35;&2=35&3=TBD> |
| Sets the amplitude of the current modulation to AMP. AMP is an integer ranging from 0 – 255. Command returns the output of the command **DitherA?**((Not implemented as of November, 2017)) | Sets the amplitude of the current modulation to AMP. AMP is an integer ranging from 0 – 255. Command returns the output of the command **DitherA?**((Not implemented as of November, 2017)) |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=Dither?&2=On&3=TBD> | <function=ICEfunc?0=Dither？&2=On&3=TBD> |
| Returns the status of the dither on the laser current (on or off).((Not implemented as of November, 2017)) | Returns the status of the dither on the laser current (on or off).((Not implemented as of November, 2017)) |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=Dither&1=A:On/Off:On;&2=On&3=TBD> | <function=ICEfunc?0=Dither&1=A:On/Off:On;&2=On&3=TBD> |
| Enables or disables the dither on the laser current. Valid arguments are On or Off. Returns the output of the command **Dither?**.((Not implemented as of November, 2017)) | Enables or disables the dither on the laser current. Valid arguments are On or Off. Returns the output of the command **Dither?**.((Not implemented as of November, 2017)) |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=ReadVolt&1=I:CHANNEL:4&2=4.234&3=38> | <function=ICEfunc?0=ReadVolt？&1=I:CHANNEL:4&2=4.234&3=38> |
| Returns the voltage measured on channel CHANNEL (in volts). The channels refer to: | Returns the voltage measured on channel CHANNEL (in volts). The channels refer to: |
| - Servo Out | - Servo Out |
| |
| |
| <function=ICEfunc|0=Servo?&2=On&3=TBD> | <function=ICEfunc?0=Servo？&2=On&3=TBD> |
| Returns the status of the servo (on or off). | Returns the status of the servo (on or off). |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=Servo&1=A:On/Off:On;&2=Off&3=TBD> | <function=ICEfunc?0=Servo&1=A:On/Off:On;&2=Off&3=TBD> |
| Turns on the servo (engages the integrators). Returns the output of the command **Servo?**. | Turns on the servo (engages the integrators). Returns the output of the command **Servo?**. |
| <html></div></html> | <html></div></html> |
| |
| |
| <function=ICEfunc|0=AUXSRVO?&2=On&3=TBD>Returns the status of auxiliary servo. Note, auxiliary servo only engaged when main servo is engaged, if **AUXSRVO?** is On when **SERVO?** is Off, Auxiliary servo will engage when the main servo is engaged.<html></div></html> | <function=ICEfunc?0=AUXSRVO？&2=On&3=TBD>Returns the status of auxiliary servo. Note, auxiliary servo only engaged when main servo is engaged, if **AUXSRVO?** is On when **SERVO?** is Off, Auxiliary servo will engage when the main servo is engaged.<html></div></html> |
| |
| <function=ICEfunc|0=AUXSRVO&1=A:On/Off:Off&2=Off&3=TBD>Turns on or off the auxiliary servo. Returns the **AUXSRVO?** command. <html></div></html> | <function=ICEfunc?0=AUXSRVO&1=A:On/Off:Off&2=Off&3=TBD>Turns on or off the auxiliary servo. Returns the **AUXSRVO?** command. <html></div></html> |
| |
| |
| <function=ICEfunc|0=DCOffst?&2=-2.345&3=TBD> | <function=ICEfunc?0=DCOffst？&2=-2.345&3=TBD> |
| Returns DC offset (in volts) applied to the error signal. | Returns DC offset (in volts) applied to the error signal. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=DCOffst&1=F:OFFSET:2.340;&2=2.342&3=TBD> | <function=ICEfunc?0=DCOffst&1=F:OFFSET:2.340;&2=2.342&3=TBD> |
| Sets the DC offset (in volts) applied to the error signal to OFFSET. Returns the output of the command **DCOffst?**. The range of the values is set by the **DCMODE** command. In mode 1, the range is -5V to 5V. In mode 2, the range is -10V to 0V. In mode 3, the range is 0V - 10V. | Sets the DC offset (in volts) applied to the error signal to OFFSET. Returns the output of the command **DCOffst?**. The range of the values is set by the **DCMODE** command. In mode 1, the range is -5V to 5V. In mode 2, the range is -10V to 0V. In mode 3, the range is 0V - 10V. |
| <html></div></html> | <html></div></html> |
| |
| |
| <function=ICEfunc|0=Gain?&2=25&3=TBD> | <function=ICEfunc?0=Gain？&2=25&3=TBD> |
| Returns Servo Gain. Range is from -33 to 30 in steps of 1 dB. | Returns Servo Gain. Range is from -33 to 30 in steps of 1 dB. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=Gain&1=I:GAIN:24;&2=24&3=TBD> | <function=ICEfunc?0=Gain&1=I:GAIN:24;&2=24&3=TBD> |
| Sets the Servo Gain. Range is from -33 to 30 dB in steps of 1 dB. Returns the output of the command **Gain?** | Sets the Servo Gain. Range is from -33 to 30 dB in steps of 1 dB. Returns the output of the command **Gain?** |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=OpOfst1?&2=129&3=45> | <function=ICEfunc?0=OpOfst1？&2=129&3=45> |
| Returns First Integrator Op-Amp’s Offset Voltage adjustment value. Range is 0-255, with 128 being in the middle. This should not need adjustment and generally should be left at its default value. | Returns First Integrator Op-Amp’s Offset Voltage adjustment value. Range is 0-255, with 128 being in the middle. This should not need adjustment and generally should be left at its default value. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=OpOfst1&1=I:OFFSET:142;&2=142&3=46> | <function=ICEfunc?0=OpOfst1&1=I:OFFSET:142;&2=142&3=46> |
| Sets the First Integrator Op-Amp’s Offset Voltage adjustment value. This should be factory set, but it controls the DC Error Input voltage that the servo locks to (should be 0V) OFFSET is an integer from 0-255. Returns the output of the command **OpOfst1?**. | Sets the First Integrator Op-Amp’s Offset Voltage adjustment value. This should be factory set, but it controls the DC Error Input voltage that the servo locks to (should be 0V) OFFSET is an integer from 0-255. Returns the output of the command **OpOfst1?**. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=OpOfst2?&2=129&3=45> | <function=ICEfunc?0=OpOfst2？&2=129&3=45> |
| Returns Second Integrator Op-Amp’s Offset Voltage adjustment value. Range is 0-255, with 128 being in the middle. This should not need adjustment and generally should be left at its default value. | Returns Second Integrator Op-Amp’s Offset Voltage adjustment value. Range is 0-255, with 128 being in the middle. This should not need adjustment and generally should be left at its default value. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=OpOfst2&1=I:OFFSET:142;&2=142&3=46> | <function=ICEfunc?0=OpOfst2&1=I:OFFSET:142;&2=142&3=46> |
| Sets the Second Integrator Op-Amp’s Offset Voltage adjustment value. This should be factory set, but it controls the DC Error Input voltage that the servo locks to (should be 0V) OFFSET is an integer from 0-255. Returns the output of the command **OpOfst3?**. | Sets the Second Integrator Op-Amp’s Offset Voltage adjustment value. This should be factory set, but it controls the DC Error Input voltage that the servo locks to (should be 0V) OFFSET is an integer from 0-255. Returns the output of the command **OpOfst3?**. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=SvOffst?&2=2.341&3=TBD> | <function=ICEfunc?0=SvOffst&2=2.341&3=TBD> |
| Returns Servo Offset voltage (in volts). When the servo is engaged, this voltage is the starting voltage that the servo integrates from. | Returns Servo Offset voltage (in volts). When the servo is engaged, this voltage is the starting voltage that the servo integrates from. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=SvOffst&1=F:OFFSET:-1.232;&2=-1.23&3=TBD> | <function=ICEfunc?0=SvOffst&1=F:OFFSET:-1.232;&2=-1.23&3=TBD> |
| Sets the Servo Offset voltage (in volts) to OUTPUT when the servo is turned off. When the servo is engaged, this voltage is the starting voltage that the servo integrates from. Returns the output of the command **SvOffst?**. | Sets the Servo Offset voltage (in volts) to OUTPUT when the servo is turned off. When the servo is engaged, this voltage is the starting voltage that the servo integrates from. Returns the output of the command **SvOffst?**. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=AxOffst?&2=2.341&3=TBD> | <function=ICEfunc?0=AxOffst？&2=2.341&3=TBD> |
| Returns Aux Servo Offset voltage (in volts). When the aux servo is engaged, this voltage is the starting voltage that the aux servo integrates from. | Returns Aux Servo Offset voltage (in volts). When the aux servo is engaged, this voltage is the starting voltage that the aux servo integrates from. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=AxOffst&1=F:OFFSET:-1.232;&2=-1.23&3=TBD> | <function=ICEfunc?0=AxOffst&1=F:OFFSET:-1.232;&2=-1.23&3=TBD> |
| Sets the Aux Servo Offset voltage (in volts) to OFFSET when the servo is turned off. When the aux servo is engaged, this voltage is the starting voltage that the servo integrates from. Returns the output of the command **AxOffst?**. | Sets the Aux Servo Offset voltage (in volts) to OFFSET when the servo is turned off. When the aux servo is engaged, this voltage is the starting voltage that the servo integrates from. Returns the output of the command **AxOffst?**. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=DataChn?&2=2&3=TBD> | <function=ICEfunc?0=DataChn&2=2&3=TBD> |
| Read Data Channel Mode. There are 3 modes for the Data Channel: | Read Data Channel Mode. There are 3 modes for the Data Channel: |
| Mode 1: Record DC Error | Mode 1: Record DC Error |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=DataChn&1=I:CHN_MODE:3&2=3&3=TBD> | <function=ICEfunc?0=DataChn&1=I:CHN_MODE:3&2=3&3=TBD> |
| Sets the Data Channel Mode. See **DataChn?** for more details Returns the output of the command **DataChn?**. | Sets the Data Channel Mode. See **DataChn?** for more details Returns the output of the command **DataChn?**. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=RampSwp?&2=5.72&3=TBD> | <function=ICEfunc?0=RampSwp&2=5.72&3=TBD> |
| Reads the sweep range (in volts) for the ramp. | Reads the sweep range (in volts) for the ramp. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=RampSwp&1=F:VOLTAGE:2.64&2=2.65&3=TBD> | <function=ICEfunc?0=RampSwp&1=F:VOLTAGE:2.64&2=2.65&3=TBD> |
| Writes the sweep range (in volts) for the ramp. Range is from -10V to +10V. Returns the output from the command **RampSwp?**.\\ | Writes the sweep range (in volts) for the ramp. Range is from -10V to +10V. Returns the output from the command **RampSwp?**.\\ |
| \\ | \\ |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=RampNum?&2=100&3=TBD> | <function=ICEfunc?0=RampNum？&2=100&3=TBD> |
| Returns the number of data points to be acquired during the ramp. Number of data points is also the number of steps for the ramp. | Returns the number of data points to be acquired during the ramp. Number of data points is also the number of steps for the ramp. |
| |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=RampNum&1=I:NUMBER:100&2=100&3=TBD> | <function=ICEfunc?0=RampNum&1=I:NUMBER:100&2=100&3=TBD> |
| Sets the number of data points to be acquired during the ramp. Number of data points is also the number of steps for the ramp. Number of data points to calculated by the following formula: | Sets the number of data points to be acquired during the ramp. Number of data points is also the number of steps for the ramp. Number of data points to calculated by the following formula: |
| |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=RampRun&2=Busy&3=TBD> | <function=ICEfunc?0=RampRun&2=Busy&3=TBD> |
| Begins ramping the servo output and taking data according to the values set for **RampInc**, **RampBeg**, and **RampEnd** as described above. Data can be retrieved with the **ReadBlk** command. Board will not respond to any new commands while taking data. Returns status of execution of the ramp, either Busy or Finished. Returns fault if ramp is misconfigured. See **RampNum?** for details. At end of ramp, servo output is set to **SVOffst?** value. | Begins ramping the servo output and taking data according to the values set for **RampInc**, **RampBeg**, and **RampEnd** as described above. Data can be retrieved with the **ReadBlk** command. Board will not respond to any new commands while taking data. Returns status of execution of the ramp, either Busy or Finished. Returns fault if ramp is misconfigured. See **RampNum?** for details. At end of ramp, servo output is set to **SVOffst?** value. |
| <html></div></html> | <html></div></html> |
| |
| |
| <function=ICEfunc|0=I1POLE?&2=5&3=TBD>Returns the first integrator pole position. Value of 0 is proportional only. Values 1-16 correspond to poles from 30 Hz to 175 kHz. <html></div></html> | <function=ICEfunc?0=I1POLE？&2=5&3=TBD>Returns the first integrator pole position. Value of 0 is proportional only. Values 1-16 correspond to poles from 30 Hz to 175 kHz. <html></div></html> |
| |
| <function=ICEfunc|0=I1POLE&1=I:POLE:3&2=3&3=TBD>Sets the first integrator pole position and returns the output of the command **I1POLE?** See **I1POLE?** description for details on pole values. | <function=ICEfunc?0=I1POLE&1=I:POLE:3&2=3&3=TBD>Sets the first integrator pole position and returns the output of the command **I1POLE?** See **I1POLE?** description for details on pole values. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=I2POLE?&2=7&3=TBD>Returns the second integrator pole position. Value of 0 is proportional only. Values 1-16 correspond to poles from 300 Hz to 1.75 MHz. <html></div></html> | <function=ICEfunc?0=I2POLE？&2=7&3=TBD>Returns the second integrator pole position. Value of 0 is proportional only. Values 1-16 correspond to poles from 300 Hz to 1.75 MHz. <html></div></html> |
| |
| <function=ICEfunc|0=I2POLE&1=I:POLE:6&2=6&3=TBD>Sets the second integrator pole position and returns the output of the command **I2POLE?** See **I2POLE?** description for details on pole values. | <function=ICEfunc?0=I2POLE&1=I:POLE:6&2=6&3=TBD>Sets the second integrator pole position and returns the output of the command **I2POLE?** See **I2POLE?** description for details on pole values. |
| <html></div></html> | <html></div></html> |
| |
| <function=ICEfunc|0=DPOLE?&2=12&3=TBD>Returns the differential pole position. Value of 0 is no differential. Values 1-16 correspond to poles from 100 Hz to 10 MHz. <html></div></html> | <function=ICEfunc?0=DPOLE？&2=12&3=TBD>Returns the differential pole position. Value of 0 is no differential. Values 1-16 correspond to poles from 100 Hz to 10 MHz. <html></div></html> |
| |
| <function=ICEfunc|0=DPOLE&1=I:POLE:6&2=6&3=TBD>Sets the differential pole position and returns the output of the command **DPOLE?** See **DPOLE?** description for details on pole values. | <function=ICEfunc?0=DPOLE&1=I:POLE:6&2=6&3=TBD>Sets the differential pole position and returns the output of the command **DPOLE?** See **DPOLE?** description for details on pole values. |
| <html></div></html> | <html></div></html> |
| |
| |
| <function=ICEfunc|0=DCMODE?&2=On&3=TBD>Returns the DC Offset Mode used to set the DC Offset. There are 3 modes: | <function=ICEfunc?0=DCMODE？&2=On&3=TBD>Returns the DC Offset Mode used to set the DC Offset. There are 3 modes: |
| - DC Offset Range: -5V - 5V | - DC Offset Range: -5V - 5V |
| - DC Offset Range: -10V - 0V | - DC Offset Range: -10V - 0V |
| |
| <html></div></html> | <html></div></html> |
| <function=ICEfunc|0=DCMODE&1=I:MODE:2&2=2&3=TBD>Sets the DC Offset Mode. See **DCMODE?** for details on the different modes. Changing the DC Offset Mode will change the DC Offset and should be re-set via the **DCOFFST** command after running the **DCMODE** command. | <function=ICEfunc?0=DCMODE&1=I:MODE:2&2=2&3=TBD>Sets the DC Offset Mode. See **DCMODE?** for details on the different modes. Changing the DC Offset Mode will change the DC Offset and should be re-set via the **DCOFFST** command after running the **DCMODE** command. |
| <html></div></html> | <html></div></html> |
| |
| |
| <function=ICEfunc|0=AUXMODE?&2=3&3=TBD>Returns the Gain Mode for the auxiliary servo. Values or 1, 2 or 3, corresponding to low, medium and high.<html></div></html> | <function=ICEfunc?0=AUXMODE？&2=3&3=TBD>Returns the Gain Mode for the auxiliary servo. Values or 1, 2 or 3, corresponding to low, medium and high.<html></div></html> |
| |
| <function=ICEfunc|0=AUXMODE&1=I:MODE:2&2=2&3=TBD>Sets the Gain Mode of the auxiliary servo. Valid values are 1, 2 or 3, corresponding to low, medium and high.<html></div></html> | <function=ICEfunc?0=AUXMODE&1=I:MODE:2&2=2&3=TBD>Sets the Gain Mode of the auxiliary servo. Valid values are 1, 2 or 3, corresponding to low, medium and high.<html></div></html> |
| |
| <function=ICEfunc|0=AUXGAIN?&2=15&3=TBD>Returns the gain (0-255) for the auxiliary servo loop. The scale is linear, not log, so 4 is four times more gain than 1 and 250 is 20% more than 200. The total loop gain is set by both the AUXGAIN and the AUXMODE. Each increment in AUXMODE increase that gain by ~250, or nearly the fully range of the AUXGAIN setting.<html></div></html> | <function=ICEfunc?0=AUXGAIN？&2=15&3=TBD>Returns the gain (0-255) for the auxiliary servo loop. The scale is linear, not log, so 4 is four times more gain than 1 and 250 is 20% more than 200. The total loop gain is set by both the AUXGAIN and the AUXMODE. Each increment in AUXMODE increase that gain by ~250, or nearly the fully range of the AUXGAIN setting.<html></div></html> |
| |
| <function=ICEfunc|0=AUXGAIN&1=I:GAIN:54&2=54&3=TBD>Sets the Aux Gain and returns the output from the **AUXGAIN?** command. See **AUXGAIN?** for more details.<html></div></html> | <function=ICEfunc?0=AUXGAIN&1=I:GAIN:54&2=54&3=TBD>Sets the Aux Gain and returns the output from the **AUXGAIN?** command. See **AUXGAIN?** for more details.<html></div></html> |
| |
| |
| |
| |
| <function=ICEfunc|0=AUXINVT?&2=On&3=TBD>Returns whether the auxiliary servo loop inverts its input or not.<html></div></html> | <function=ICEfunc?0=AUXINVT？&2=On&3=TBD>Returns whether the auxiliary servo loop inverts its input or not.<html></div></html> |
| |
| <function=ICEfunc|0=AUXINVT&1=A:INVERT:Off&2=Off&3=TBD>Sets whether or not to invert the input to Auxiliary servo loop. INVERT should be "On" or "Off".<html></div></html> | <function=ICEfunc?0=AUXINVT&1=A:INVERT:Off&2=Off&3=TBD>Sets whether or not to invert the input to Auxiliary servo loop. INVERT should be "On" or "Off".<html></div></html> |
| |
| |
| <function=ICEfunc|0=INVERT?&2=On&3=TBD>Returns whether the Error In signal is inverted.<html></div></html> | <function=ICEfunc?0=INVERT？&2=On&3=TBD>Returns whether the Error In signal is inverted.<html></div></html> |
| <function=ICEfunc|0=INVERT&1=A:INVERT:Off&2=Off&3=TBD>Sets whether or not to invert the Error Input signal. INVERT should be "On" or "Off".<html></div></html> | <function=ICEfunc?0=INVERT&1=A:INVERT:Off&2=Off&3=TBD>Sets whether or not to invert the Error Input signal. INVERT should be "On" or "Off".<html></div></html> |
| |
| <function=ICEfunc|0=AUXMIN?&2=-5.1&3=TBD>Returns the minimum voltage that the auxiliary servo can output. Voltage output is coerced to this value if output tried to go lower than this value. <html></div></html> | <function=ICEfunc?0=AUXMIN？&2=-5.1&3=TBD>Returns the minimum voltage that the auxiliary servo can output. Voltage output is coerced to this value if output tried to go lower than this value. <html></div></html> |
| <function=ICEfunc|0=AUXMIN&1=F:VOLTAGE:2.415&2=2.4&3=TBD>Sets the minimum value the auxiliary servo can go. See **AUXMIN?** for more details.<html></div></html> | <function=ICEfunc?0=AUXMIN&1=F:VOLTAGE:2.415&2=2.4&3=TBD>Sets the minimum value the auxiliary servo can go. See **AUXMIN?** for more details.<html></div></html> |
| |
| |
| <function=ICEfunc|0=AUXMAX?&2=On&3=TBD>Returns the maximum voltage that the auxiliary servo can output. Voltage output is coerced to this value if output tried to go higher than this value. <html></div></html> | <function=ICEfunc?0=AUXMAX？&2=On&3=TBD>Returns the maximum voltage that the auxiliary servo can output. Voltage output is coerced to this value if output tried to go higher than this value. <html></div></html> |
| |
| <function=ICEfunc|0=AUXMAX&1=F:VOLTAGE:7.215&2=7.2&3=TBD>Sets the maximum value the auxiliary servo can go. See **AUXMAX?** for more details.<html></div></html> | <function=ICEfunc?0=AUXMAX&1=F:VOLTAGE:7.215&2=7.2&3=TBD>Sets the maximum value the auxiliary servo can go. See **AUXMAX?** for more details.<html></div></html> |
| |
| <function=ICEfunc|0=SVOMIN?&2=-5.1&3=TBD>Returns the minimum voltage that the servo can output. Voltage output is coerced to this value if output tried to go lower than this value. <html></div></html> | <function=ICEfunc?0=SVOMIN？&2=-5.1&3=TBD>Returns the minimum voltage that the servo can output. Voltage output is coerced to this value if output tried to go lower than this value. <html></div></html> |
| <function=ICEfunc|0=SVOMIN&1=F:VOLTAGE:2.415&2=2.4&3=TBD>Sets the minimum value the servo can go. See **SVOMIN?** for more details.<html></div></html> | <function=ICEfunc?0=SVOMIN&1=F:VOLTAGE:2.415&2=2.4&3=TBD>Sets the minimum value the servo can go. See **SVOMIN?** for more details.<html></div></html> |
| |
| |
| <function=ICEfunc|0=SVOMAX?&2=On&3=TBD>Returns the maximum voltage that the servo can output. Voltage output is coerced to this value if output tried to go higher than this value. <html></div></html> | <function=ICEfunc?0=SVOMAX？&2=On&3=TBD>Returns the maximum voltage that the servo can output. Voltage output is coerced to this value if output tried to go higher than this value. <html></div></html> |
| |
| <function=ICEfunc|0=SVOMAX&1=F:VOLTAGE:7.215&2=7.2&3=TBD>Sets the maximum value the servo can go. See **SVOMAX?** for more details.<html></div></html> | <function=ICEfunc?0=SVOMAX&1=F:VOLTAGE:7.215&2=7.2&3=TBD>Sets the maximum value the servo can go. See **SVOMAX?** for more details.<html></div></html> |
| |
| |
| |
| <function=ICEfunc|0=JUMPSRVO&1=A:JUMP:On&2=On&3=TBD>Used for debugging and loop optimization only, toggles the Servo Offset from its current value to -1 times its current value. For use when servo engaged and monitor how servo responds to challenge of jumping the servo offset. Argument is either "On" or "Off".<html></div></html> | <function=ICEfunc?0=JUMPSRVO&1=A:JUMP:On&2=On&3=TBD>Used for debugging and loop optimization only, toggles the Servo Offset from its current value to -1 times its current value. For use when servo engaged and monitor how servo responds to challenge of jumping the servo offset. Argument is either "On" or "Off".<html></div></html> |
| |
