Product Manuals

User Tools

Site Tools

You are here: manuals » d2 » spectroscopy_module_212
d2:spectroscopy_module_212

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
d2:spectroscopy_module_212 [2016/09/15 00:46] – [Inputs, Outputs, and Controls] Michael Radunskyd2:spectroscopy_module_212 [2018/08/24 22:02] – [Inputs, Outputs, and Controls] DokuWiki Administrator
Line 78: Line 78:
 **Input Connector**** (****6-pin circular)** **Input Connector**** (****6-pin circular)**
  
-Power from the D2-005 Power Supply, ICE-PB1 Power Buss, or other power supply are made through a Hirose 6-pin circular connector ([[http://www.digikey.com/product-detail/en/HR10A-7TR-6SA/HR357-ND/510211|HR10A-7TR-6SA]]) shown in <imgref front>.  The pin definitions (pin numbers are marked on the connectors) are listed in <tabref connector>.+Power from the D2-005 Power Supply, ICE-PB1 Power Buss, or other power supply are made through a Hirose 6-pin circular connector ([[http://www.digikey.com/product-detail/en/HR10A-7TR-6SA/HR357-ND/510211|HR10A-7TR-6SA]]) shown in <imgref front> and <imgref hirose_pinout>.  The pin definitions (pin numbers are marked on the connectors) are listed in <tabref connector>.
  
-<imgcaption image1|Pin numbering on female Hirose 6-pin connector>{{  :d2:d2-160:hirose-connector.png?200  }}</imgcaption>+<imgcaption hirose_pinout|Pin numbering on female Hirose 6-pin connector>{{  :d2:d2-160:hirose-connector.png?200  }}</imgcaption>
  
 <WRAP center round box 900px><tabcaption connector> <WRAP center round box 900px><tabcaption connector>
Line 105: Line 105:
  
 The extent of the trim range can be determined by probing the location shown in <imgref trimpots2> with a voltmeter referenced to case ground (the outer shell of the SMA connector is a good reference point). Probing this location gives the wiper voltage of the trimpot which corresponds to temperature as shown in the table below. This 10-turn trim pot sets temperature from 15°C (fully CCW) to 75°C (10 turns CW).  The 5-turn point is approximately 42°C. The following table gives approximate temperature settings for the three available alkali options: The extent of the trim range can be determined by probing the location shown in <imgref trimpots2> with a voltmeter referenced to case ground (the outer shell of the SMA connector is a good reference point). Probing this location gives the wiper voltage of the trimpot which corresponds to temperature as shown in the table below. This 10-turn trim pot sets temperature from 15°C (fully CCW) to 75°C (10 turns CW).  The 5-turn point is approximately 42°C. The following table gives approximate temperature settings for the three available alkali options:
-<WRAP center round box 300px>+<WRAP center round box 300px><tabcaption temperature>
 ^ Alkali ^  Turns CW  ^  Wiper Voltage  ^  Temp  ^ ^ Alkali ^  Turns CW  ^  Wiper Voltage  ^  Temp  ^
 | cesium |  2  |  6.8V  |  ~30°C  | | cesium |  2  |  6.8V  |  ~30°C  |
 | rubidium |  4-5  |  5.7V  |  ~40°C  | | rubidium |  4-5  |  5.7V  |  ~40°C  |
 | potassium |  8-9  |  3.9V  |  ~60°C  | | potassium |  8-9  |  3.9V  |  ~60°C  |
-</WRAP>+</tabcaption></WRAP>
  
 **Window Offset Adjustment** **Window Offset Adjustment**
d2/spectroscopy_module_212.txt · Last modified: 2023/04/18 16:31 by 127.0.0.1