User Tools

Site Tools


d2:spectroscopy_module_210

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
d2:spectroscopy_module_210 [2019/05/31 13:44] – [Purchase Includes] Michael Radunskyd2:spectroscopy_module_210 [2020/03/16 22:17] – [Theory of Operation] Michael Radunsky
Line 72: Line 72:
 The remaining portion is passed through a fixed λ/2 waveplate and PBS to split off the pump beam from the probe beam.  The pump beam is directed to the Output Optics assembly where it is combined with the probe beam on a PBS in a counter-propagating configuration. The pump beam is dumped through the reflection port of the PBS that separated the pump and probe and terminates on the wall of the housing.  The probe is detected on the signal photodiode. The remaining portion is passed through a fixed λ/2 waveplate and PBS to split off the pump beam from the probe beam.  The pump beam is directed to the Output Optics assembly where it is combined with the probe beam on a PBS in a counter-propagating configuration. The pump beam is dumped through the reflection port of the PBS that separated the pump and probe and terminates on the wall of the housing.  The probe is detected on the signal photodiode.
  
-The beam diameters were designed to provide enough photocurrent (~50-100μA) to give shot-noise-limited performance out to 5 MHz while limiting saturation broadening.  For Vescent's DBR lasers, the bandwidth is useful to provide for tight and stable locking by feedback to injection current.  +The beam diameters were designed to provide enough photocurrent (~50-100 μA) to give shot-noise-limited performance out to 5 MHz while limiting saturation broadening.  For Vescent's DBR lasers, the bandwidth is useful to provide for tight and stable locking by feedback to injection current.  
  
  
Line 125: Line 125:
 **Temperature Bias Adj.** **Temperature Bias Adj.**
  
-For the Doppler subtraction option this control enables the user to input a small temperature difference between the reference and signal vapor cells.  In the fully CCW position the signal vapor cell heater gets all the current.  In the full CW position the reference cell heater gets twice the current as the signal cell.  This adjustment can be used to place the optimum point for Doppler Subtraction closer to zero Volts.+[Note: this adjustment is only available on older D2-210 models.] For the Doppler subtraction option this control enables the user to input a small temperature difference between the reference and signal vapor cells.  In the fully CCW position the signal vapor cell heater gets all the current.  In the full CW position the reference cell heater gets twice the current as the signal cell.  This adjustment can be used to place the optimum point for Doppler Subtraction closer to zero Volts.
  
 This adjustment only has an effect with the -DS, Doppler Subtraction option. This adjustment only has an effect with the -DS, Doppler Subtraction option.
Line 190: Line 190:
  
  
-The following images are representative of spectroscopy for <sup>87</sup>Rb with and without Doppler subtraction.  Note that Doppler subtraction has a minimal effect on peak lock signal generated by dithering the laser (green traces).+The following images are representative of spectroscopy for <sup>87</sup>Rb with and without Doppler subtraction.  Note that Doppler subtraction (<imgref ds>has a minimal effect on peak lock signal generated by dithering the laser (green traces).
  
 +<imgcaption image1|Pin numbering on female Hirose 6-pin connector>{{  :d2:d2-160:hirose-connector.png?200  }}</imgcaption>
  
-{{ :d2:d2-210:sas.jpg?nolink |}} +<imgcaption no-ds|Non-Doppler subtracted side- and peak-lock spectra>{{ :d2:d2-210:sas.jpg?nolink |}}</imgcaption> 
-{{ :d2:d2-210:sas_w_ds.jpg?nolink |}}+<imgcaption ds|Doppler subtracted side- and peak-lock spectra>{{ :d2:d2-210:sas_w_ds.jpg?nolink |}}</imgcaption>
d2/spectroscopy_module_210.txt · Last modified: 2024/03/27 15:58 by Thomas Bersano