User Tools

Site Tools


d2:spectroscopy_module_210

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
d2:spectroscopy_module_210 [2016/08/30 17:57] – [Specifications] Michael Radunskyd2:spectroscopy_module_210 [2019/06/18 20:48] – [Aligning the Spectroscopy Module] Michael Radunsky
Line 27: Line 27:
   * D2-210 Spectroscopy Module   * D2-210 Spectroscopy Module
   * VPN00463 SMA cable (6ft)   * VPN00463 SMA cable (6ft)
-Also look for: 
   * VPN00410 Hirose-to-D Sub 9-pin (shipped under separate line item; specify for use with D2)   * VPN00410 Hirose-to-D Sub 9-pin (shipped under separate line item; specify for use with D2)
   * VPN00475 Hirose-to-Hirose power cord (shipped under separate line item; specify for use with ICE)   * VPN00475 Hirose-to-Hirose power cord (shipped under separate line item; specify for use with ICE)
 +  * VPN00367 Adjustment tool
  
  
Line 45: Line 45:
 =====Specifications===== =====Specifications=====
 <WRAP center round box 500px><tabcaption specs> <WRAP center round box 500px><tabcaption specs>
-^ ^  Value  ^  Units  +                                   ^  Value          ^  Units   
-^**Input Light Level**  |  2< P <1000  |  mW  +^ **Input Light Level**              |  2< P <1000     |  mW      
-^**Photodiode Amplifier**        +^ **Photodiode Amplifier**                                    
-<html> &nbsp;&nbsp; </html>  Transimpedance (signal) |  40,000  |  Ω  +| Transimpedance (signal)            |  40,000         |  Ω       
-<html> &nbsp;&nbsp; </html>Bandwidth (signal) |  5  |  MHz  +| Bandwidth (signal)                 |  5              |  MHz     
-<html> &nbsp;&nbsp; </html>Noise @ 5 MHz  |  <80  |  nV / <HTML> <span style="text-decoration: overline;">Hz</span></HTML> +| Noise @ 5 MHz                      |  <80            |  nV /√Hz | 
-^Set Temperature  |  ~25 to 65  |  °C  +^ Set Temperature                    |  ~25 to 65      |  °C      
-^Temperature Stability|  <0.1  |  °C  +^ Temperature Stability              |  <0.1           |  °C      
-^Beam Height|  0.95  |  inches +^ Beam Height                        |  0.95           |  inches 
-^Total package Size \\ (L x W x H)|  3.6 x 5 x 1.7  |  inches  |+^ Total package Size \\ (L x W x H)  |  3.6 x 5 x 1.7  |  inches  |
 </tabcaption> </tabcaption>
 </WRAP> </WRAP>
Line 61: Line 61:
 The D2-210 requires +5 and ±15 VDC and ground to operate.  The power input is via a female 6-pin Hirose connector [[http://www.digikey.com/product-search/en?KeyWords=HR10A-7TR-6SA(73)&WT.z_header=search_go|HR10A-7TR-6SA(73)]].  Depending on your order configuration, you should have received a power cable with this connector on one end and either the same on the other end (typically for use with ICE products) or a DB-9 connector (for use with D2-products). The D2-210 requires +5 and ±15 VDC and ground to operate.  The power input is via a female 6-pin Hirose connector [[http://www.digikey.com/product-search/en?KeyWords=HR10A-7TR-6SA(73)&WT.z_header=search_go|HR10A-7TR-6SA(73)]].  Depending on your order configuration, you should have received a power cable with this connector on one end and either the same on the other end (typically for use with ICE products) or a DB-9 connector (for use with D2-products).
  
-If you are using the DB9-to-Hirose cable, but not a Vescent D2-005 power supply, <tabref connector> below details which pins on the Hirose require which voltages.  The figure below may be useful. +If you are using the DB9-to-Hirose cable, but not a Vescent D2-005 power supply, <tabref connector> below details which pins on the Hirose require which voltages.  
- +
-<imgcaption image1|Pin numbering on female Hirose 6-pin connector>{{:d2:d2-160:hirose-connector.png?200 }}</imgcaption>+
 =====Theory of Operation===== =====Theory of Operation=====
 <WRAP center round box 620px> <WRAP center round box 620px>
  
-[{{ :d2:d2-210:d2-210_top.jpg?nolink&600 |D2-210 Spectroscopy Module with cover removed.}}]</WRAP> +<imgcaption 210_drawing|Beam path and component map>[{{ :d2:d2-210:d2-210_top.jpg?nolink&600 |D2-210 Spectroscopy Module with cover removed.}}]</imgcaption></WRAP> 
-<WRAP center round box 420px>[{{ :d2:d2-210:d2-210-temp-adjust.jpg?400 |2nd revision of temperature control board}}]</WRAP>+<WRAP center round box 420px><imgcaption temp_adj_photo>[{{ :d2:d2-210:d2-210-temp-adjust.jpg?400 |2nd revision of temperature control board}}]</imgcaption></WRAP>
  
 Input light passes through an adjustable λ/2 waveplate and polarizing beamsplitter (PBS) that directs a user-controlled portion of the beam to the vapor cells and detectors.  (For the fiber-coupled option the user will generally input most of the light.) The beam is then passed through a cleanup PBS and split on a 50:50 non-polarizing beamsplitter (NPBS).  One portion is then passed through a reference vapor cell (Doppler subtraction option) or passed directly to the reference photodiode. Input light passes through an adjustable λ/2 waveplate and polarizing beamsplitter (PBS) that directs a user-controlled portion of the beam to the vapor cells and detectors.  (For the fiber-coupled option the user will generally input most of the light.) The beam is then passed through a cleanup PBS and split on a 50:50 non-polarizing beamsplitter (NPBS).  One portion is then passed through a reference vapor cell (Doppler subtraction option) or passed directly to the reference photodiode.
Line 80: Line 78:
  
 **Input Connector**** (****6-pin circular)** **Input Connector**** (****6-pin circular)**
 +<WRAP center round important 60%>Never connect this device to its power supply when the power supply is switched on and supplying power.  Always turn off the power supply, make connections to the device, and then re-energize the power supply.
 +</WRAP>
 +
 +Power and temperature control signals from the D2-series power bus, the ICE-PB1, or other power supply are made through a 6-pin circular connector ([[http://www.digikey.com/product-search/en?KeyWords=HR10A-7TR-6SA(73)&WT.z_header=search_go|HR10A-7TR-6SA(73)]]).  The pin definitions (pin numbers are marked on the connectors) are listed below.  <imgref image1> below may be useful.
  
-Power and temperature control signals from the D2-series power bus or other power supply are made through a 6-pin circular connector ([[http://www.digikey.com/product-search/en?KeyWords=HR10A-7TR-6SA(73)&WT.z_header=search_go|HR10A-7TR-6SA(73)]]).  The pin definitions (pin numbers are marked on the connectors) are listed below.+<imgcaption image1|Pin numbering on female Hirose 6-pin connector>{{  :d2:d2-160:hirose-connector.png?200  }}</imgcaption>
  
-<WRAP center round box 500px><tabcaption connector> +<WRAP center round box 900px><tabcaption connector> 
-^  Pin  ^  Input Voltage  ^  Max Current Draw  ^ Notes ^ +^  Hirose Pin   DB-9 Pin (if applicable)   Input Voltage  ^  Max Current Draw  ^  Notes  
-|  1  |  Signal Ground  | | Return path for voltages on pins 5 & 6. | +|  1  |  4 and 5   |  Signal Power Ground  | | Return path for power rail. | 
-|  2  |  -7 V to -15 V  |  100mA  | See note below. | +|  2    -7 V to -15 V  |  100mA  | See note below. | 
-|  3  |  +7 V to +15 V  |  100 mA  | See note below. | +|  3    +7 V to +15 V  |  100 mA  | See note below. | 
-|  4  |  +5 V  |  1.5 A / 2.5 A  | 2.5 A max with Doppler subtraction option, 1.5 A max without. | +|  4  |  6 and 7   |  +5 V  |  1.5 A / 2.5 A  | 2.5 A max with Doppler subtraction option, 1.5 A max without. | 
-|  5  |  No Connect  | | +|  5  |  No Connect  | | 
-|  6  |  +5 V Ground  | | Return path for high current +5V. |+|  6   1 and 2   +5 V Ground  | | Return path for high current +5V. |
 </tabcaption></WRAP> </tabcaption></WRAP>
 <wrap lo>Note:  When powering the D2-210 with supplies other than a D2-005, pins 5 and 6 can be placed between 7-15 V. They need not be symmetric, but both supply rails are always required.</wrap> <wrap lo>Note:  When powering the D2-210 with supplies other than a D2-005, pins 5 and 6 can be placed between 7-15 V. They need not be symmetric, but both supply rails are always required.</wrap>
Line 129: Line 131:
 **Tilt Plate** **Tilt Plate**
  
-A polarizing beamsplitter (PBS) is fixed to a ball joint formed by a truncated steel ball held by a conformal brass ring.  Two cone screws clamp the ring against the ball and fix the position of the PBS.  See Alignment Procedure below for instructions on how to align and fix the PBS.{{ :d2:d2-210:tilt_plate.png?nolink&400 |}}+A polarizing beamsplitter (PBS) is fixed to a ball joint formed by a truncated steel ball held by a conformal brass ring.  Two cone screws clamp the ring against the ball and fix the position of the PBS.  See Alignment Procedure below for instructions on how to align and fix the PBS.<WRAP center round box 420px> 
 + 
 +<imgcaption tilt_plate|Input beam tilt plate adjustment>{{ :d2:d2-210:tilt_plate.png?nolink&400 |}}</imgcaption></WRAP>
  
 **λ/2 Waveplate** **λ/2 Waveplate**
Line 135: Line 139:
 A waveplate attached to the front plate by magnets can be used to select the splitting fraction of the Tilt Plate PBS. A waveplate attached to the front plate by magnets can be used to select the splitting fraction of the Tilt Plate PBS.
  
-{{ :d2:d2-210:halfwave_adjuster.jpg?nolink&400 |}}+<WRAP center round box 420px> 
 + 
 +<imgcaption halfwaveplate|Half wave plate adjuster>{{ :d2:d2-210:halfwave_adjuster.jpg?nolink&400 |}}</imgcaption></WRAP>
  
  
Line 184: Line 190:
  
  
-The following images are representative of spectroscopy for <sup>87</sup>Rb with and without Doppler subtraction.  Note that Doppler subtraction has a minimal effect on peak lock signal generated by dithering the laser (green traces).+The following images are representative of spectroscopy for <sup>87</sup>Rb with and without Doppler subtraction.  Note that Doppler subtraction (<imgref ds>has a minimal effect on peak lock signal generated by dithering the laser (green traces).
  
 +<imgcaption image1|Pin numbering on female Hirose 6-pin connector>{{  :d2:d2-160:hirose-connector.png?200  }}</imgcaption>
  
-{{ :d2:d2-210:sas.jpg?nolink |}} +<imgcaption no-ds|Non-Doppler subtracted side- and peak-lock spectra>{{ :d2:d2-210:sas.jpg?nolink |}}</imgcaption> 
-{{ :d2:d2-210:sas_w_ds.jpg?nolink |}}+<imgcaption ds|Doppler subtracted side- and peak-lock spectra>{{ :d2:d2-210:sas_w_ds.jpg?nolink |}}</imgcaption>
d2/spectroscopy_module_210.txt · Last modified: 2024/03/27 15:58 by Thomas Bersano