User Tools

Site Tools


d2:quick_start_opls

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
d2:quick_start_opls [2015/08/22 00:02] – [D2-150 Alignment] Michael Radunskyd2:quick_start_opls [2021/08/26 15:26] (current) – external edit 127.0.0.1
Line 1: Line 1:
 ====== Quick Setup Instructions (Offset Phase Lock D2-135) ====== ====== Quick Setup Instructions (Offset Phase Lock D2-135) ======
 +
 +//Please see the full [[d2:offset_phase_lock_servo|D2-135 manual]] for more detail on the performance, specifications, and features of this product.//\\
  
 //Please refer to the [[d2:quick_start|Quick Setup Instructions]] for setting up the electronics modules and connecting the Laser Controller to the Lasers.//  //Please refer to the [[d2:quick_start|Quick Setup Instructions]] for setting up the electronics modules and connecting the Laser Controller to the Lasers.// 
Line 5: Line 7:
 At this point you should have two lasers temperature stabilized and running at their operating current. The two lasers should be within a few GHz of the same frequency of each other. (If unsure of the laser frequency, you can use a spectroscopy module to get one laser on transition and then temporarily move the spectroscopy module to the other laser to get it near the same transition.) At this point you should have two lasers temperature stabilized and running at their operating current. The two lasers should be within a few GHz of the same frequency of each other. (If unsure of the laser frequency, you can use a spectroscopy module to get one laser on transition and then temporarily move the spectroscopy module to the other laser to get it near the same transition.)
  
-===== D2-150 Alignment =====+===== D2-250 or D2-150 Alignment =====
  
-//This section assumes you are using the [[d2:heterodyne_module|D2-150 Heterodyne Module]] to obtain an optical beat note between two lasers. If you have obtained an optical beat note by other methods, please skip this section.// +//This section assumes you are using the [[d2:heterodyne_module|D2-150 Heterodyne Module]] to obtain an optical beat note between two lasers. If you have obtained an optical beat note by other methods, please skip this section.   
 + 
 +The new [[d2:d2_250_heterodyne_module|D2-250 Heterodyne Module]] has replaced the D2-150.  Alignment of the D2-250 is similar to that of the D2-150.// 
  
  
 <WRAP left round box 350px> <WRAP left round box 350px>
-<imgcaption d2-150-schematic|Schematic drawing of the laser alignment in to the D2-150 Heterodyne Module.>{{:d2:d2-150:d2-150_heterodyne-schematic.jpg?nolink| }}</imgcaption>+<imgcaption d2-150-schematic|Schematic drawing of the laser alignment into the D2-150 Heterodyne Module.>{{:d2:d2-150:d2-150_heterodyne-schematic.jpg?nolink| }}</imgcaption>
  
 +</WRAP><WRAP left round box 350px>
 +<imgcaption d2-250-schematic|Schematic drawing of the laser alignment into the new D2-250 Heterodyne Module.>{{:d2:d2_250:d2-250_schematic.png?nolink| }}</imgcaption>
 </WRAP> </WRAP>
  
-Place the two lasers and the D2-150 as shown in <imgref d2-150-schematic>: the two lasers oriented 90° relative to each other and both pointing at the D2-150. Take the top off the D2-150 and place it such that the beams of both lasers hit the center of the first beam splitter that they encounter. There are 3 adjustable beam splitters in the D2-150: two for aligning one laser, and one for aligning the other laser. In <imgref d2-150-schematic> the master laser is the laser with only one adjustment because it passes straight-through the second beam splitter on its way to fiber, while the slave laser reflects at 90° off of two beam splitters. It is important to align the laser with only one adjustment stage first (the master laser in the figure). +Place the two lasers and the D2-150 or D2-250 as shown in either <imgref d2-150-schematic> or <imgref d2-250-schematic> depending on which unit you are using: the two lasers oriented 90° relative to each other and both pointing at the Heterodyne Module. Take the top off the D2-250 (-150and place it such that the beams of both lasers hit the center of the first beam splitter that they encounter. There are 3 adjustable beam splitters in the D2-150: two for aligning one laser, and one for aligning the other laser. In <imgref d2-150-schematic> the master laser is the laser with only one adjustment because it passes straight-through the second beam splitter on its way to fiber, while the slave laser reflects at 90° off of two beam splitters. It is important to align the laser with only one adjustment stage first (the master laser in the figure). 
  
 === First Laser Alignment === === First Laser Alignment ===
  
-Use a power meter to measure the power out from the fiber connected to the D2-150. Block the laser that has two adjustments and measure the power from the laser with one adjustment that gets coupled into the fiber. Use the two adjustments on the beam splitter that affects the laser position to maximize the power into the fiber. If you cannot measure any light from the fiber, it is often helpful to put light into the fiber (opposite direction from how the system operates) and see how well that light gets back to the laser. Adjust the same beam splitter so the light is aimed directly at the laser source. This should get the alignment close enough to measure the power in the fiber to use for further optimization. Aim for 500 μW of power although a few hundred microwatts should be sufficient. <html><span style="color:red">The detector in the D2-160 or D2-135-FC can be damaged by more than 1 mW input power, so be careful not to couple in too much light.</span></html>+Use a power meter to measure the power out from the fiber connected to the D2-150. Block the laser that has two adjustments and measure the power from the laser with one adjustment that gets coupled into the fiber. Use the two adjustments on the beam splitter that affects the laser position to maximize the power into the fiber. If you cannot measure any light from the fiber, it is often helpful to put light into the fiber (opposite direction from how the system operates) and see how well that light gets back to the laser. Adjust the same beam splitter so the light is aimed directly at the laser source. This should get the alignment close enough to measure the power in the fiber to use for further optimization. Aim for 500 μW of power although a few hundred microwatts should be sufficient. <color red>The detector in the D2-160 or D2-135-FC can be damaged by more than 1 mW input power, so be careful not to couple in too much light.</color>
  
 === Second Laser Alignment === === Second Laser Alignment ===
Line 27: Line 33:
 === Finding a Beat Note === === Finding a Beat Note ===
  
-<WRAP right round box 450px><imgcaption image1|Initial electrical connections to D2-135.  (As shown for D2-135-SMA.  For D2-135-FC, connect optical output of D2-150 directly to SC fiber input on face of D2-135.)>{{:d2:quick_start_opls:d2-135_connections.jpg?direct&400 |}}</imgcaption></WRAP>+<WRAP right round box 450px><imgcaption image1|Initial electrical connections to D2-135.  (As shown for D2-135-SMA.  For D2-135-FC, connect optical output of D2-150 or D2-250 directly to SC fiber input on face of D2-135.)>{{:d2:quick_start_opls:d2-135_connections.jpg?direct&400 |}}</imgcaption></WRAP>
  
-Plug the fiber into either the D2-160 or D2-135-FC (obsolete). If using the D2-160, use a short RF SMA cable to connect the D2-160 to the D2-135-SMA. Look at the D2-135's Beat Note div/2 monitor on a spectrum analyzer. You should see a beat note at half the frequency difference between the two lasers. You may need to tweak the laser current on one laser to make sure the frequency difference is in range. Once you see a beat note, adjust the laser frequency until the beat note starts to broaden or disappear. When that happens, park the laser where the beat note starts to degrade and tweak the alignment of the 3 beam splitters until the beat note looks good. Repeat until you have the desired frequency range (typically ~10 GHz).+Plug the fiber into either the D2-160 or D2-135-FC (obsolete). If using the D2-160, use a short RF SMA cable to connect the D2-160 to the D2-135-SMA. Look at the D2-135's Beat Note div/2 monitor on a spectrum analyzer. You should see a beat note at half the frequency difference between the two lasers. You may need to tweak the laser current on one laser to make sure the frequency difference is in range. Once you see a beat note, adjust the laser frequency until the beat note starts to broaden or disappear. When that happens, park the laser where the beat note starts to degrade and tweak the alignment of the 3 beam splitters until the beat note looks good. Repeat until you have the desired frequency offset (typically up to ~10 GHz).
 ===== D2-135 Locking ===== ===== D2-135 Locking =====
  
 Getting a phase lock can be tricky, as the servo feedback must be pretty well optimized to your laser to get a phase lock. The narrower the linewidth of the laser and the higher the bandwidth of the laser, the easier it is to get a phase lock. The first step is to get an error signal with a steep slope at the desired offset frequency and then a basic lock.  Getting a phase lock can be tricky, as the servo feedback must be pretty well optimized to your laser to get a phase lock. The narrower the linewidth of the laser and the higher the bandwidth of the laser, the easier it is to get a phase lock. The first step is to get an error signal with a steep slope at the desired offset frequency and then a basic lock. 
  
-Connect the D2-135's Servo Out to the Servo In on your Laser Controller to sweep the slave laser's frequency. (Refer to <imgref image1> for making electrical connections to the D2-135.) Connect the Ramp TTL on the D2-135 to the trigger on your O-scope and view the Error In Monitor to the O-scope. Set the D2-135 to N=16, VCO Low mode, put the Servo in Ramp mode and by tweaking the laser current, you should see the Error In Monitor look something like what is shown in <imgref error_signal>.<WRAP left round box 450px><imgcaption error_signal|Sample Error Signal when sweeping one laser. Reflection point shown in blue, two lock point shown in red.>{{:d2:quick_start_opls:opls-sweep-figure.png?direct&400 |}}</imgcaption></WRAP>+Connect the D2-135's Servo Out to the Servo In on your Laser Controller to sweep the slave laser's frequency. (Refer to <imgref image1> for making electrical connections to the D2-135.) Connect the Ramp TTL on the D2-135 to the trigger on your O-scope and view the Error In Monitor to the O-scope. Set the D2-135 to N=16, VCO Low mode, put the Servo in Ramp mode and by tweaking the laser current, you should see the Error In Monitor look something like what is shown in <imgref error_signal>.<WRAP left round box 450px><imgcaption error_signal|Sample Error Signal when sweeping one laser. Reflection point is shown in blue, two lock points are shown in red.>{{:d2:quick_start_opls:opls-sweep-figure.png?direct&400 |}}</imgcaption></WRAP>
  
  
  
-The reflection point on the Error Signal is where the two lasers are at the same frequency. The Error Signal is even function of offset frequency (Error(Δf) = Error(-Δf)), so there is a reflection point about Δf=0. The sharp slope to the left or right of the Δf=0 point is the lock point and can be adjusted by changing the VCO frequency. Which of the two lock points the laser will lock to will depend on the gain sign. Center the O-scope on one of the lock points and turn down the ramp amplitude. Flip the D2-135 Servo to Lock mode. If the Servo Output jumps to +/-10V, repeat with the opposite gain sign. At this point, you should have a lock that is holding the offset frequency to a specific value. You may be be significantly broadening the laser because the servo is oscillating, but you have a basic lock.+The reflection point on the Error Signal is where the two lasers are at the same frequency. The Error Signal is an even function of offset frequency (Error(Δf) = Error(-Δf)), so there is a reflection point about Δf=0. The sharp slope to the left or right of the Δf=0 point is the lock point and can be adjusted by changing the VCO frequency. Which of the two lock points the laser will lock to will depend on the gain sign. Center the O-scope on one of the lock points and turn down the ramp amplitude. Flip the D2-135 Servo to Lock mode. If the Servo Output jumps to +/-10V, repeat with the opposite gain sign. At this point, you should have a lock that is holding the offset frequency to a specific value. You may be significantly broadening the laser because the servo is oscillating, but you have a basic lock.
  
 === Optimizing the Lock === === Optimizing the Lock ===
Line 52: Line 58:
 For further assistance, contact us at:\\ For further assistance, contact us at:\\
 +1 (303) 296-6766 or\\ +1 (303) 296-6766 or\\
-<[email protected]>+<[email protected]>\\ 
 + 
 +//Please see the full [[d2:offset_phase_lock_servo|D2-135 manual]] for more detail on the performance, specifications, and features of this product.//\\ 
d2/quick_start_opls.1440201763.txt.gz · Last modified: 2021/08/26 14:26 (external edit)