d2:laser_servo
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
d2:laser_servo [2019/09/06 17:16] – [Right Side Panel] Michael Radunsky | d2:laser_servo [2021/03/02 17:06] – [Specifications] Michael Radunsky | ||
---|---|---|---|
Line 21: | Line 21: | ||
The D2-125 Reconfigurable Laser Servo contains a tunable PI< | The D2-125 Reconfigurable Laser Servo contains a tunable PI< | ||
- | The main component in the Reconfigurable Laser Servo is the PI< | + | The main component in the Reconfigurable Laser Servo is the PI< |
The Laser Servo can be unlocked by a computer (via TTL control) to jump the output voltage to a set voltage difference from the current lock point, or to a specific voltage. This feature can be used to jump the laser frequency a known distance away and then relock to the original or a new lock point frequency. This feature can be used for auto-locking or relocking routines. | The Laser Servo can be unlocked by a computer (via TTL control) to jump the output voltage to a set voltage difference from the current lock point, or to a specific voltage. This feature can be used to jump the laser frequency a known distance away and then relock to the original or a new lock point frequency. This feature can be used for auto-locking or relocking routines. | ||
Line 67: | Line 67: | ||
<WRAP center round box 600px> | <WRAP center round box 600px> | ||
| | **Value** | | | **Value** | ||
- | | **Input and Output Impedance** | + | | **Input and Output Impedance** |
| **Output Voltage (main and aux)** | | **Output Voltage (main and aux)** | ||
| **Input Voltage Noise**(( Referenced to 50Ω load)) | | **Input Voltage Noise**(( Referenced to 50Ω load)) | ||
Line 267: | Line 267: | ||
** Aux: Bipolar / Aux: Unipolar (2-position slider switch) ** | ** Aux: Bipolar / Aux: Unipolar (2-position slider switch) ** | ||
- | This 2-position slider switch is only accessible by removing the right side panel (see above) and sets whether the AUXILIARY OUTPUT SERVO is unipolar or bipolar. It is factory set to be bipolar so the auxiliary output can range from -12 V to +12 V. For some applications such as driving a PZT, limiting the voltage range to positive values is necessary. | + | This 2-position slider switch is only accessible by removing the right side panel (see above) and sets whether the AUXILIARY OUTPUT SERVO is unipolar or bipolar. It is factory set to be bipolar so the auxiliary output can range from -10 V to +10 V. For some applications such as driving a PZT, limiting the voltage range to positive values is necessary. |
**Ramp Master / Slave (Jumper)** | **Ramp Master / Slave (Jumper)** | ||
Line 273: | Line 273: | ||
This jumper is only accessible by removing the right side panel (see above) and sets whether the ramp input is in master or slave mode. It is factory set to be in MASTER MODE. In SLAVE MODE (jumper off) the RAMP signal is generated externally and input through the back panel RAMP I/O port. In MASTER MODE (jumper on) the ramp is generated internally and is sent out to the RAMP I/O port for driving other D2-125 Laser Servos configured in SLAVE MODE. | This jumper is only accessible by removing the right side panel (see above) and sets whether the ramp input is in master or slave mode. It is factory set to be in MASTER MODE. In SLAVE MODE (jumper off) the RAMP signal is generated externally and input through the back panel RAMP I/O port. In MASTER MODE (jumper on) the ramp is generated internally and is sent out to the RAMP I/O port for driving other D2-125 Laser Servos configured in SLAVE MODE. | ||
- | The slave ramp is multiplied by about -5x (at slave Ramp Amp maximum) | + | The amplitude of the slave ramp is about -5x of the master ramp input (at slave Ramp Amp maximum). The DC offset is applied |
====Lock Guard==== | ====Lock Guard==== | ||
Line 291: | Line 291: | ||
<WRAP center round box 400px> | <WRAP center round box 400px> | ||
| **C** | **B** | **A** | ** Hold Time** | | **C** | **B** | **A** | ** Hold Time** | ||
- | |0ff|0ff|0ff| 60 µs | 150 µs | | + | |Off|Off|Off| 60 µs | 150 µs | |
- | |0ff|0ff|0n| 125µs | + | |Off|Off|On| 125µs |
- | |0ff|On|0ff| 250 µs | 600 µs | | + | |Off|On|Off| 250 µs | 600 µs | |
- | |0ff|0n|0n| 500 µs | 1.25 ms | | + | |Off|On|On| 500 µs | 1.25 ms | |
- | |0n|0ff|0ff| 1 ms | 2.5 ms | | + | |On|Off|Off| 1 ms | 2.5 ms | |
- | |0n|0ff|0n| 2 ms | 5 ms | | + | |On|Off|On| 2 ms | 5 ms | |
- | |0n|On|0ff| 4 ms | 10 ms | | + | |On|On|Off| 4 ms | 10 ms | |
- | |0n|0n|0n| 8 ms | 20 ms | | + | |On|On|On| 8 ms | 20 ms | |
</ | </ | ||
Line 320: | Line 320: | ||
**Absolute Jump TTL (BNC)** | **Absolute Jump TTL (BNC)** | ||
- | When asserted HIGH (5V) while in LOCK mode, ABSOLUTE JUMP takes the Laser Servo out of lock and conveys the voltage on LASER JUMP AMPLITUDE to the SERVO OUTPUT. | + | When asserted HIGH (5V) while in LOCK mode, ABSOLUTE JUMP takes the Laser Servo out of lock and conveys |
- | When asserted HIGH (5V) while in RAMP mode, ABSOLULTE | + | When asserted HIGH (5V) while in RAMP mode, ABSOLUTE |
- | When disconnected, | + | When disconnected, |
**Relative Jump TTL (BNC)** | **Relative Jump TTL (BNC)** | ||
- | When asserted HIGH (5 V) while in LOCK mode, RELATIVE JUMP engages a sample-and-hold circuit and takes the Laser Servo out of lock. The voltage on the SERVO OUTPUT is the sample-and-hold value summed in with the LASER JUMP AMPLITUDE. For example, if the laser is locked and the SERVO OUTPUT is -200 mV, then engaging the RELATIVE JUMP and putting 300 mV on the LASER JUMP AMPLITUDE will make the SERVO OUTPUT | + | When asserted HIGH (5 V) while in LOCK mode, RELATIVE JUMP engages a sample-and-hold circuit and takes the Laser Servo out of lock. The voltage on the SERVO OUTPUT is the sample-and-hold value summed in with <color black/ |
When asserted HIGH (5V) while in RAMP mode, RELATIVE JUMP applies a DC offset equal to the LASER JUMP AMPLITUDE to the ramp signal at SERVO OUTPUT. When asserted LOW (0V) while in RAMP mode, the ramp signal is DC balanced. | When asserted HIGH (5V) while in RAMP mode, RELATIVE JUMP applies a DC offset equal to the LASER JUMP AMPLITUDE to the ramp signal at SERVO OUTPUT. When asserted LOW (0V) while in RAMP mode, the ramp signal is DC balanced. |
d2/laser_servo.txt · Last modified: 2021/12/17 01:58 by 127.0.0.1