Product Manuals

User Tools

Site Tools

You are here: manuals » waveguide » manuals » ls-15-3005
waveguide:manuals:ls-15-3005

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
waveguide:manuals:ls-15-3005 [2016/01/15 04:13] – [Operation] Michael Radunskywaveguide:manuals:ls-15-3005 [2016/01/19 00:22] – [Connections and Controls] Michael Radunsky
Line 38: Line 38:
 <color red>WARNING</color> <color red>WARNING</color>
 Do not clean outside surfaces of any Vescent Photonics products with solvents such as acetone. Front panels on electronics modules may be cleaned with a mild soap and water solution. Do not clean optics modules.  Do not clean outside surfaces of any Vescent Photonics products with solvents such as acetone. Front panels on electronics modules may be cleaned with a mild soap and water solution. Do not clean optics modules. 
 +
 +<color red>WARNING</color>
 +The user should NEVER disconnect the  control cable from the scanner or driver while power is applied ("hot swapping"). Since the devices does not have internal pull-downs to ground, any voltage left on the device could permanently damage it, causing reduced throughput, highly degraded beam quality, and large in-plane scattering.
  
 ==Limited Warranty== ==Limited Warranty==
Line 43: Line 46:
 Vescent Photonics shall not be obligated to furnish service under this warranty from damage caused by service or repair attempts made without authorization by Vescent Photonics; from damage caused by operation of equipment outside of its specified range as stated in either the product specifications or operators manual; from damage due to improper connection to other equipment or power supplies.  Vescent Photonics shall not be obligated to furnish service under this warranty from damage caused by service or repair attempts made without authorization by Vescent Photonics; from damage caused by operation of equipment outside of its specified range as stated in either the product specifications or operators manual; from damage due to improper connection to other equipment or power supplies. 
 This warranty is in lieu of all other warranties including any implied warranty concerning the suitability or fitness of the product for a particular use. Vescent Photonics shall only be liable for the cost of repairs or replacement of the defective product within the warranty period. Vescent Photonics shall not be liable for any damages to persons or property resulting from the use of the product or caused by the defect or failure of this product. Vescent Photonics' liability is expressly limited to the warranty set out above. By accepting delivery of this product, the purchaser expressly agrees to the terms of this limited warranty. This warranty is in lieu of all other warranties including any implied warranty concerning the suitability or fitness of the product for a particular use. Vescent Photonics shall only be liable for the cost of repairs or replacement of the defective product within the warranty period. Vescent Photonics shall not be liable for any damages to persons or property resulting from the use of the product or caused by the defect or failure of this product. Vescent Photonics' liability is expressly limited to the warranty set out above. By accepting delivery of this product, the purchaser expressly agrees to the terms of this limited warranty.
-Vescent Photonics 
  
 +<WRAP center round box 400px>[{{ :waveguide:manuals:4_pedestal.png?350|Figure 4. SEEOR 2D beam steerer.}}]
 +</WRAP>
 =====Operating Parameters===== =====Operating Parameters=====
 Absolute Maximum Ratings Absolute Maximum Ratings
Line 95: Line 99:
 The scanner is packaged with a PM fiber pigtail (see Figure 4) with an FC/PC connector. This is an engineering package and not intended for field use.  Its input must be linearly polarized light with the polarization axis parallel to the FC key.  The scanner is packaged with a PM fiber pigtail (see Figure 4) with an FC/PC connector. This is an engineering package and not intended for field use.  Its input must be linearly polarized light with the polarization axis parallel to the FC key. 
 =====Connections and Controls===== =====Connections and Controls=====
 +<color red>WARNING</color>
 +The user should NEVER disconnect the  control cable from the scanner or driver while power is applied ("hot swapping"). Since the devices does not have internal pull-downs to ground, any voltage left on the device could permanently damage it, causing reduced throughput, highly degraded beam quality, and large in-plane scattering.
  
 With the power switch in the OFF or down position (see Figure 5) connect the power supply to the wall plug and to the LS-105 back panel (see Figure 6).  Use the provided cable to connect the LS-105 driver to the SEEOR unit.  The unit is now ready to be powered on.  The driver provides up to 110 V to the beam steerer.  Please operate safely. With the power switch in the OFF or down position (see Figure 5) connect the power supply to the wall plug and to the LS-105 back panel (see Figure 6).  Use the provided cable to connect the LS-105 driver to the SEEOR unit.  The unit is now ready to be powered on.  The driver provides up to 110 V to the beam steerer.  Please operate safely.