ice:master
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
ice:master [2014/07/03 18:01] – [Absolute Maximum Ratings] jtshugrue | ice:master [2014/07/03 18:05] – [I/O] jtshugrue | ||
---|---|---|---|
Line 22: | Line 22: | ||
===== Specifications | ===== Specifications | ||
- | <WRAP center round box 550px> | ||
^ ^ Min ^ Typ ^ Max ^ Units ^ | ^ ^ Min ^ Typ ^ Max ^ Units ^ | ||
- | ^ Input Power Requirements((Minimum recommended supply current depends on configuration and number of daughter boards.))^ | + | ^ Input Power Requirements((Minimum recommended supply current depends on configuration and number of daughter boards.))^^^^^ |
|5V Supply Current| | |5V Supply Current| | ||
|15V Supply Current| | |15V Supply Current| | ||
Line 31: | Line 30: | ||
|15V Line Input Range| | |15V Line Input Range| | ||
|-15V Line Input Range| | |-15V Line Input Range| | ||
- | ^ Maximum Power Consumption((External power provided must also be able to handle the current requirements to utilize maximum power consumption specification)) ^ ^ ^ | + | ^ Maximum Power Consumption((External power provided must also be able to handle the current requirements to utilize maximum power consumption specification)) |
|5V Current Draw| - | - | 10 | A | | |5V Current Draw| - | - | 10 | A | | ||
|15V Current Draw| - | - | 3 | A | | |15V Current Draw| - | - | 3 | A | | ||
|-15V Current Draw| - | - | 3 | A | | |-15V Current Draw| - | - | 3 | A | | ||
- | ^ D-Sub 9pin Signals ^ | + | ^ D-Sub 9pin Signals |
|Safety Interlock Input Voltage Range| | |Safety Interlock Input Voltage Range| | ||
|TXO Serial Input Voltage Range| | |TXO Serial Input Voltage Range| | ||
Line 43: | Line 42: | ||
|5V Input Voltage Range| | |5V Input Voltage Range| | ||
|5V Input Current Draw| - | 25 | 40 | mA | | |5V Input Current Draw| - | 25 | 40 | mA | | ||
- | ^ Slave Boards ^ ^ ^ | + | ^ Slave Boards |
|Max Number of Slave Boards | - | - | 8 | | | |Max Number of Slave Boards | - | - | 8 | | | ||
- | ^ Communication Methods ^ ^ ^ | + | ^ Communication Methods |
|I2C Bus | | | | |I2C Bus | | | | ||
|TTL Serial (3.3V) | | | | |TTL Serial (3.3V) | | | | ||
- | </ | + | |
- | <WRAP center round box 60%> | + | |
^ICE-MC1 Quiescent Power Draw((Power consumption with no daughter boards connected.))^^^^^ | ^ICE-MC1 Quiescent Power Draw((Power consumption with no daughter boards connected.))^^^^^ | ||
^ ^ Min ^ Typical | ^ ^ Min ^ Typical | ||
Line 55: | Line 53: | ||
|+15V Current Draw | | | 5 | mA | | |+15V Current Draw | | | 5 | mA | | ||
|-15V Current Draw | | | 5 | mA | | |-15V Current Draw | | | 5 | mA | | ||
- | </ | + | |
===== I/O ===== | ===== I/O ===== | ||
Line 77: | Line 75: | ||
Communication with the Master Controller and daughter modules is done through flat flex connecter J11. This connector contains two serial UART bi-directional communication busses, event system GPIO pins, and a safety interlock signal. | Communication with the Master Controller and daughter modules is done through flat flex connecter J11. This connector contains two serial UART bi-directional communication busses, event system GPIO pins, and a safety interlock signal. | ||
J11 is a 12-pin 1.00mm pitch flat flex connector (FCI SFW12R-1STE1LF) with a pin definition shown in <tabref backpanelffc> | J11 is a 12-pin 1.00mm pitch flat flex connector (FCI SFW12R-1STE1LF) with a pin definition shown in <tabref backpanelffc> | ||
+ | |||
+ | < | ||
< | < | ||
^ **Pin** | ^ **Pin** | ||
Line 92: | Line 92: | ||
| 12 | Safety Interlock | | 12 | Safety Interlock | ||
</ | </ | ||
+ | </ | ||
+ | |||
== Serial UART == | == Serial UART == |
ice/master.txt · Last modified: 2021/08/26 15:26 by 127.0.0.1